Equipment
2013 TaylorMade RocketBladez Tech Specs & Video
The best part of TaylorMade’s RocketBladez irons isn’t the long distances that they fly, according to TaylorMade engineers. It’s the consistent distance that the irons fly on mishits.
TaylorMade has made long-flying irons in the past, one of their most popular being the two-year-old Burner 2.0 irons. But those and other “game-improvement” irons haven’t been popular with better players because they tend to cause problems with distance control. Irons such as the Burner 2.0s have what’s called a hotspot, a place above the center of the clubface that when struck with clean contact causes shots to fly longer-than-anticipated distances. This is bad because unlike drivers, skilled golfers aren’t trying to hit their irons as far as possible. They’re trying to hit them a controlled distance.
[youtube id=”QpmrytE3gLI” width=”600″ height=”350″]
Click here for more discussion in the “Tour/Pre-release equipment” forum.
Bret Wahl, TaylorMade’s vice president of R&D for irons, said that he and his team have spent the last five years designing irons with a higher coefficient of restitution, or COR. A high COR is achieved by making clubfaces thinner, increasing the spring-like effect and making the ball fly farther. But even though engineers were able to increase speed on shots hit on the center of the clubface, they struggled to add a similar amount of speed to mishits, especially shots hit on the stiff, lower portion of the face that is attached to the leading edge of the club.
The performance of the lower portion of the clubface is important for golfers because according to a TaylorMade study 72 percent of shots are struck below the center of the clubface. That means that almost three-quarters of all golf shots are not hit with optimal speed.
Last year, TaylorMade released its RocketBallz fairway woods and hybrids, the first of the company’s clubs to include its “Speed Pocket,” a slot on the bottom of the sole near the leading edge that increased COR. This added speed and forgiveness to the clubface, especially on shots struck below the center where the Speed Pocket functioned to make the lower portion of the clubface more flexible.
RocketBladez bring Speed Pocket technology to irons, and like the RocketBallz fairway woods and hybrids before them, the company is promising more speed and forgiveness. How much speed and forgiveness a golfer will get, however, depends on which model of RocketBladez irons they choose.
RocketBladez Tour Irons
TaylorMade’s two most popular irons on the PGA Tour are the company’s Forged MB and CB models, thick-faced irons that provide slow speeds on center strikes. But even though they lack the speed of distance irons on shots hit on the center of the face, the MBs and CBs are more consistent than other models on slight mishits and have no hotspots.
According to Gary Gallagher, market manager for metal woods for TaylorMade, there was no desire on Tour for substantially longer-flying irons. That’s why instead of giving RocketBladez Tour irons the “full steroid” treatment that designers gave the non-Tour RocketBladez, engineers held back, only adding “a quarter of a steroid” to their ingredient list.
The RocketBladez Tour irons were designed to mimic the aesthetics of the Forged CBs. They have thin soles, a small amount of offset and similar blade lengths and toplines. But the Speed Pocket in the sole increases the COR to 0.819, adding at least 1 mph of ball speed to center strikes and making the sweetspot of the RocketBladez Tour five times larger than the Forged CBs (note: TaylorMade defines the sweetspot as the area of the clubface where there is less than a 1 mph drop off in speed).
Like the RocketBallz fairway woods and hybrids, the Speed Pocket increases ball speed as well as launch angle, which gives Tour players two options with RocketBladez Tour irons. They can:
- Hit the RocketBladez Tour irons higher and a little further than their current irons (the current average off added distance according to Gallagher is 8 yards).
- Bend the lofts stronger, giving them an iron that flies as high as their current model but goes substantially further.
The RocketBladez Tour 3 iron through 7 iron are cast from 17-4 stainless steel, which adds the necessary stiffness for construction. To make the irons feel softer, the Speed Pocket is filled with a special polyurethane developed by 3M that still allows the pocket to flex and reduces vibrations. It also limits debris that could enter the pocket.
The Speed Pocket is not used in the 8 iron, 9 iron, pitching wedge and “attack wedge,” however, because Gallagher said the speed pocket becomes less active and thus less important as loft is added to the club. Since the short irons are slotless, they can be cast from a softer material, 431 stainless steel. The distance gap between the 7 iron and 8 iron is bridged gradually by varying the different variables of the irons — mainly loft, face thickness and the depth of the speed pocket throughout the set.
RocketBladez Irons
Click here for more photos of the RocketBladez irons
The RocketBladez (non-Tour) irons lose the wacky geometry of last year’s RBZ irons in favor of a more traditional game-improvement iron shape, resembling the Burner 2.0 irons at address. They have the same COR as the Tours, but they have thicker soles, thicker top lines, more offset and a longer blade profile to support a deeper center of gravity (CG) position. This makes makes them more longer and more forgiving than the Tours and 5 mph faster than the Burner 2.0s, which accounts for double-digit distance gains.
Like the Tours, the RocketBladez employ a slot in the 3 through 7 irons and no slot on the 8 iron, 9 iron, pitching wedge and A-wedge. They are also available in a 55-degree sand wedge and 60-degree lob wedge that use TaylorMade’s ATV sole grind. Take a look at the specs below for more information.
Click here for more discussion in the “Tour/Pre-release equipment” forum.
Tour Edge Golf has today introduced the all-new Exotics mini driver, engineered to deliver a powerful combination of speed, control, and versatility in the long game.
The Exotics Mini combines a titanium face with a stainless-steel body in design to balance ball speed with stability and control, creating a versatile option at the top end of the bag.
At the core of the design is Tour Edge’s proprietary Combo Brazing technology, a high-precision thermal bonding process that seamlessly fuses a titanium cup face to a stainless-steel body into a single, continuous structure. By eliminating energy loss found in traditional multi-piece constructions, Combo Brazing is designed to deliver faster face response, more efficient energy transfer, and a uniquely powerful yet controlled feel.
The multi-material construction also allows mass to be positioned lower and deeper in the head in a bid to increase stability, while the thin titanium face is engineered to maintain ball speed across a wider impact area.
“While the initial goal was to enhance control and versatility in the long game, Combo Brazing ultimately drove measurable gains in ball speed and distance within the mini driver category. In robot testing, we’ve documented higher ball speeds, higher launch, reduced spin, and increased carry and total distance compared to leading models.” – Vice President of R&D Matt Neeley
In addition to distance performance, the Exotics mini emphasizes forgiveness through a heavier stainless-steel body that shifts mass toward the perimeter. This configuration increases MOI relative to traditional all-titanium mini drivers, helping preserve ball speed and directional stability on off-center strikes. Paired with Pyramid Face Technology from the Exotics metalwood line, the design is intended to support consistent speed across the face.
To further enhance MOI, a lightweight carbon fiber crown frees additional mass that is strategically repositioned low and deep in the head in design to improve stability and promote optimal launch with controlled spin.
“We designed the Mini to be about five millimeters shallower than other mini drivers on the market. That change improves playability off the deck. From a clean fairway lie, it can function as a strong 3-wood alternative while still providing control off the tee.” – Tour Edge CEO David Glod
An adjustable hosel system allows for loft and lie tuning to dial in trajectory and shot shape, while a fixed 13-gram rear weight helps stabilize the head through impact to improve dispersion consistency. The Exotics Mini Driver is available in 11.5 and 13.5-degree lofts in right-handed models.
Pricing & Availability
The Exotics Mini Driver is available for pre-order beginning today for $399.99 USD at touredge.com, and will be available for purchase at retail outlets worldwide on May 22, 2026.
In our forums, our members have been pitting a Srixon ZXi combo against a TaylorMade P7CB/770 combo. WRXer ‘edutch22’ is on the hunt for a new set of irons and kicks off the thread saying:
“Looking at picking up a new set of irons and think I’ve narrowed it down to Srixon ZXi combo or Taylormade P7CB/770 combo. I am currently a 5 cap and allbeit I feel irons are my weakness. My miss is a little to the toe side. I am decently steep at 4-5 down. Always thought I am high spin but recently on trackman my 7 was spinning at 5800 roughly.
My question or looking for thoughts on which one would benefit me more from a forgiveness standpoint? Or is there another iron is should be looking at entirely? I only get to play about once or twice a week, if I am not playing a 2-3 day event. Thanks in advance.”
And our members have been sharing their thoughts and suggestions in response.
Here are a few posts from the thread, but make sure to check out the entire discussion and have your say at the link below.
- manima1: “You just can’t go wrong with Srixon ZXi7.”
- MattM97: “You have to hit them to know, the V-Sole on the Srixon can be make or break for many.”
- dmeeksDC: “P7CB is more forgiving for me than ZXi7 because my main miss is low middle and the P7CB still flies and spins great on that miss. These are both really nice irons but I like the P7CB more than the Zxi7 and the P770 (or P790) more than the Zxi5. The Srixons are larger so if that gives you confidence that is the way to go. I don’t feel like I get any benefit from the V-sole and the P7CBs live up to their high Maltby forgiveness rating so the TaylorMades have been great for me.”
Entire Thread: “Srixon ZXi combo or TaylorMade P7CB/770 combo? – GolfWRXers discuss”
At GolfWRX, we are a community of like-minded individuals who all experience and express our enjoyment of the game in many ways.
It’s that sense of community that drives day-to-day interactions in the forums on topics that range from best driver to what marker you use to mark your ball. It even allows us to share another thing we all love – buying and selling equipment.
Currently, in our GolfWRX buy/sell/trade (BST) forum, @pianoman0123 has a 2024 Wilson Staff CB/Blade combo up for grabs.
From the listing: “2024 Wilson Staff CB/Blade Combo. 4-8 irons are CB’s and the 9,PW are Blades. 5-PW have Project X 6.0 Shafts and the 4 Iron has a Steelfiber CW110 Stiff Shaft. Standard Length, Lie and Lofts. These are in very good condition the shafts just don’t work for me. Like new Lamkin Grips on the 5-PW and a stock Golf Pride on the 4 Iron. $525 OBO.”
To check out the full listing in our BST forum, head through the link. If you are curious about the rules to participate in the BST Forum, you can learn more here: GolfWRX BST Rules
RBC Heritage Tour Report: More minis, course-specific setups, Spider & GTS launches
Justin Rose WITB 2026 (April): Full WITB breakdown with new McLaren irons
Best fairway woods of 2026: The most versatile fairway woods + the most forgiving fairway woods
Gary Woodland’s winning WITB: 2026 Texas Children’s Houston Open
What’s the story behind Webb Simpson’s custom-stamped irons?
Cadillac Championship Tour Report: Spieth’s sizable changes, McLaren Golf launches, and more
The 24 players who can win the Masters
Rory McIlroy’s winning WITB: 2026 Masters
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
J.J. Spaun’s winning WITB: 2026 Valero Texas Open
Alex Fitzpatrick WITB 2026 (May)
Driver: Ping G440 LST (9 degrees) Shaft: Fujikura Ventus Black 6 X 3-wood: TaylorMade Qi4D (15 degrees) Shaft: Fujikura Ventus...
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
Driver: Ping G440 Max (9 degrees) Shaft: Mitsubishi Tensei 1K White 60 TX 3-wood: Ping G440 Max (15 degrees) Shaft:...
WITB Time Machine: Rory McIlroy’s winning WITB, 2021 Truist Championship
Rory McIlroy’s victory at the 2021 Wells Fargo Championship 2021 (now the Truist Championship) marked a significant return to form,...
Collin Morikawa WITB 2026 (May)
Driver: TaylorMade Qi4D LS (8 degrees) Shaft: Mitsubishi Diamana D+ Limited 60 TX 3-wood: TaylorMade SIM Tour (14 degrees) Shaft:...
-
Equipment2 weeks agoJustin Rose WITB 2026 (April): Full WITB breakdown with new McLaren irons
-
Equipment1 week agoWhat’s the story behind Webb Simpson’s custom-stamped irons?
-
Equipment2 weeks agoCadillac Championship Tour Report: Spieth’s sizable changes, McLaren Golf launches, and more
-
Whats in the Bag3 days ago
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
-
Whats in the Bag1 week agoCameron Young’s winning WITB: 2026 Cadillac Championship
-
Whats in the Bag3 weeks agoNelly Korda WITB 2026 (April)
-
Equipment2 weeks agoJustin Rose on the switch to McLaren Golf, learnings from previous equipment moves
-
Tour Photo Galleries2 weeks agoPhotos from the 2026 Cadillac Championship
john
Jan 3, 2013 at 6:42 pm
Just received a flyer from my local golf store abot a pre-order for rocketbladez max irons. Speed slot is in all clubs from 4-AW. Anyone heard of this or seen the sceps?
rod
Jan 9, 2013 at 4:04 pm
just 3-7 iron for the slot.
Falcon
Dec 16, 2012 at 7:25 pm
was in Bangkok recently…accidentally got to shoot on a swing simulator…i normally hit my 7 iron 150 yards on average with my R11 irons with KBS 90 R…the fitter gave me a japanese manufactured forged cavity blade with a Miyazaki C. Kua shaft…first shot went 170 yards…i was dumbfounded…then hit a few more and similar result…then bought a set of Rocket Bladez and had the same miyazaki shafts installed..and now my buddies are utterly confused how on earth i manage to hit so much longer
paul
Nov 27, 2012 at 4:27 pm
I just tried these at my local golf shop and i didn’t find the distance to be a huge gain. maybe 1 club over my current Adams a1s but the ball took off a lot faster and higher. mishits low on the face were still very good. Distance control was very good. i hit my first 5-6 shots within 2 yards of each other. i don’t think these live up to the hype but i will buy a set when i can afford new clubs in a few months.
Jeff
Nov 24, 2012 at 3:23 am
I just tested the new rocketbladez against my i20s. Rocketbladezs launched 2 degrees higher, spun between 800 to 1200 rpm less had a 10 foot higher peak trajectory and had a 2 degree steeper descent angle comparing an i20 5 iron to a rocketbladez 6 iron both having similar lofts. Both were roughly the same max distance but my thin mishits were 50 percent closer to my max distance with rocketbladez. My i20 6 iron has 3.5 degrees more loft than rocketbladez 6 iron and the same peak trajectory but was about 12 yds shorter with about 1500rpm more spin. I would like to try the rocketbladez with a dynamic gold to see if it performs better than the rocket fuel shaft. Either way distance is increased with the .819 cor face but the distance consistency is what will sell this club to mid and low handicappers.
Pingback: GolfWRX.com – 2013 TaylorMade RocketBladez Tech Specs & Video | Golf Products Reviews
Lee
Nov 14, 2012 at 12:16 pm
Just love the 6 iron comparison chart on the TM website – 6.9 yards longer than Ping i20. Considering the RocketBlade has a loft of 26.5 and the Ping i20 30 degrees aren’t we comparing a 5 iron with a 6! Then of course where it matters the scoring clubs we get larger loft spacings to fit them in. I guess the good thing is you don’t need the 3 & 4 now as they really equal 2 & 3 and you can adjust the bottom of you’re bag accordingly.
Justin
Nov 15, 2012 at 1:34 pm
Lee, you are correct seeing the difference in lofts, but what I’ve heard is that even though it’s a lower loft the ball flys higher than say a pings 6 iron for example.
NG
Nov 15, 2012 at 8:54 pm
Agree. Lee, if you had of watched the video attached to this you would find that there are many variables to determine what loft you place on each iron…you can’t and can never just compare lofts! Why does someone hit a 12 degree driver further than a 10 degree…have a think about it buddy
paul
Nov 13, 2012 at 2:36 pm
“more longer”…
Christian
Nov 17, 2012 at 12:45 pm
Correction, it “makes makes them more longer”
stephen
Nov 13, 2012 at 11:41 am
Why would you launch a product that can’t be bought for 3 months? I would like to try the tour version but would normally have my next seasons equipment in the bag over the winter to get used to it.
chris
Nov 15, 2012 at 11:54 am
Steven … I agree with you completely. I do a Super Bowl trip to Vegas end of January/early February and almost always the new stuff comes out a week later. Why not release before the holidays and take advantage of the buying season? Idiots….
Al
Nov 17, 2012 at 2:28 pm
Another expert with insults and all of the answers. Just maybe these companies pay a bunch of people a bunch of money to do their marketing analysis and it has been determined that holiday releases do not have maximum effect on sales. They likely have determined that the lemmings will fall for the marketing hype at another time of year and make their annual game-changing purchase.