Equipment

Callaway X Hot Pro 3Deep Fairway Woods

Published

13 years ago

Mar 26, 2013

Callaway’s X Hot Pro 3Deep is the third and lowest-spinning version of Callaway’s X Hot line of fairway woods to hit the PGA Tour this year.

Three different models might seem like overkill, but according to Luke Williams, senior director of global woods and irons for Callaway, they’re necessary because changing to a new 3 wood is one of the toughest equipment changes for a Tour player.

“With 3 woods, there’s two different camps,” Williams said. “There’s players that hit their 3 woods primarily off the tee and others who use it mostly off the fairway. The longer hitters use it mostly off the tee, because they very rarely are far enough out on a par 5 to need it.”

The X Hot Pro 3Deep was designed for the Tour’s longest players, those that want a very low-spinning 3 wood that they can hit almost as far as their driver off the tee. It features a noticeably deeper, or taller face, making it 25 cubic centimeters larger than the more shallow-faced X Hot Pro model.

It seems illogical that Tour players would want a driver and 3 wood that go close to the same distance, but according to Williams, it’s a setup many players use to help them shape shots both ways off the tee.

The main influencer behind the X Hot Pro 3Deep’s design was Phil Mickelson, who carries a 13-degree model and a Callaway Razr Fit Xtreme driver. Mickelson’s driver is weighted in such a way that it has a slight fade bias, which allows him to more easily create the right-to-left ball flight he prefers for control off the tee.

But if Mickelson wants to hit a draw, he can opt for his 3Deep, which is easier for him to turn over. According to Williams, the weighting of Mickelson’s 3 wood is very similar to his driver, but the 3 wood’s smaller head places the center of gravity closer to the shaft. That, combined with the fact that his 3 wood has more loft, makes it easier for him to shape shots left to right.

The X Hot Pro 3Deep is available in one loft for lefties, 13 degrees, and two lofts for righties, 13 and 14.5 degrees. The 13-degree head measures 185 cubic centimeters, while the 14.5 degree head is 180 CC’s.

Like the X Hot Pro, the 3Deep three woods feature the same 455-carpenter steel construction and warbird-inspired sole, and will come stock with True Temper Project X Velocity shafts in flexes of 5.5, 6.0 and 6.5. But they will measure 43.5 inches, 0.5-inches longer than similar X Hot Pro models.

They will be available April 19, and cost the same as the X Hot Pro fairway woods – -$229.

Check out the in-hand comparison photos we snapped of a 13-degree X Hot Pro 3Deep and 15-degree X Hot Pro fairway woods in the gallery below.

Click here for more discussion in the Tour/Pre-release equipment” forum.

: X Hot Pro 3Deep (left)

: X Hot Pro 3Deep 13 (Sole)

: X Hot Pro 3Deep (Back)

: X Hot Pro 3Deep (Top)

: X Hot Pro 3Deep (Crown)

: X Hot Pro 3Deep (Face)

: X Hot Pro 3Deep (Left)

: X Hot Pro 15 (Sole)

: X Hot Pro 3Deep (right)

: X Hot Pro 3Deep 13 (Face)

Click here for more discussion in the Tour/Pre-release equipment” forum.

Related Topics:Callaway

Up Next

Nike releases Masters Edition of the TW ’13

Don't Miss

TaylorMade Ghost Spider Blade spotted

Zak Kozuchowski

19 Comments

other paul

Nov 29, 2015 at 8:35 pm

I just finally found one of these in great shape. Swinging this at 114MPH for around 300 yards total. Love this cannon. I could leave the driver at home if I didn’t live and die by the thing.

Reply Report comment
Scott C

Jun 10, 2013 at 9:53 am

Anthony, I do remember the Callaway “Deuce”! it was outstanding. A great driver alternative that I could hit as far as my driver, but with better control. Maybe this is the replacement for the “Deuce”. I hope so.

Reply Report comment
Ji Song

May 22, 2013 at 8:14 pm

I’ve been playing with the same King Cobra Speed FD 3 wood for the past 5 years because I never found another 3 wood that I could hit farther or straighter. I was looking forward to the new Callaway XHot fairway woods and demo’ed on the course but was disappointed that I didn’t hit it any better than what I currently had. However, I recently ran across the new 3 Deep 13 degree Pro at Golfsmith and hit it on their launch monitor 285 yrds and thought their system was un-calibrated. After confirming with the employee that it was working properly, we tried several other 3+ woods and I was still hitting the 3 Deep longer and straighter more consistently. The true test was comparing it with my old 3wd. Well, the results were 15 more yards, lower launch angle, lower ball spin and less dispersion with the 3 Deep 13* with Project X 6.0 shaft (avg dist 270yrds, launch ~12*, spin 3000). I also discovered it’s only 15-20 yards shorter than a well struck driver (8.5* Ping i20 Fujikara Shaft). I ended up buying this club at full retail of $229 but excited to get out and play with it this weekend and see how long the honeymoon phase with last. Hopefully forever…

Reply Report comment
Ben

May 7, 2013 at 2:23 pm

I have tested today the x hot 3 wood and the x hot 3 wood “deep” on a simulator.
The head of the “deep” version is heavier and smaller than the head of the x hot 3 wood.
The assistant told me that this club is for player around 15 hcp or less because it is less forgiving.
I am not a long hitter but I hit today around 215 yards and pretty straight, it was really longer than my previous taylor made bought a few years ago…
I love the head of the club. The ball flight is not super high which helps the ball to hit the fairway more often.
I love this club, it will replace my driver to hit more fairways !
I eventually bought it ! It’s simply a great club.

Reply Report comment
anthony

Apr 17, 2013 at 6:17 pm

Does everybody not remember the “Deuce”??????

Reply Report comment
rj

Apr 17, 2013 at 1:10 pm

I sometimes carry an 11 degree warbird and call it a 2 wood.

Reply Report comment
Pingback: Mickelson Set To Tee Off With Phrankenwood | Mulligang Golf
Sean

Apr 8, 2013 at 8:44 am

Bumped into my local Callaway rep as well at a local range and I hit the same 13 degree with the 6.0 shaft. This club is ridiculous. Ridiculously good that is! Was hitting it as far as my new X-Hot Pro driver on most shots off the tee. For me it was too hard to hit off the deck so I will likely opt for the 14.5 loft for some versatility. It’s hard to imagine this working any better than the 15 degree Hot-Pro fairway I just got. At 43.5 inches in length, yes very much like an old school driver. It even looks like my original “Pittsburgh Persimmon” from 1987.

Reply Report comment
Bill

Mar 29, 2013 at 1:51 pm

Can’t wait to hit it, Matt…It has a 43.5 inch shaft, so it’s not a rehashed driver as some assert. The deeper face makes it desirable off the tee. More like the 2 woods of old which I often used as a youngster. I have a 19.5 hybrid for fairways and I’ve never hit driver off the deck effectively so this club absolutely has a market. Hopefully my Callaway rep is up to speed on this release now.

Reply Report comment
- Jack
  
  Apr 8, 2013 at 2:16 am
  
  That’s probably longer than the old drivers.
  
  Reply Report comment
Mat

Mar 28, 2013 at 12:12 pm

What’s old is new again. It’s basically an old-school driver, with old-school shape and old-school loft.

Reply Report comment
- Scott
  
  Mar 28, 2013 at 1:48 pm
  
  Spot on !
  
  Reply Report comment
Matt

Mar 28, 2013 at 11:59 am

I actually got to hit this yesterday at my local Golfsmith. The Callaway Rep showed up while I was hitting and comparing some irons and he asked if I had any questions since I was hitting the new Callaway Forged irons as he came in. I asked him jokingly if he had a 3 Deep on him and he in fact did have one.

He had the 13° with the Project X 6.0 shaft. First off the weight felt extremely good holding with a nice heavy head and looking down the taller face is definitely noticeable. The 6.0 shaft however did have a little more flex than I like and whips a lot with the heavy club head. I would need to try out the Project X 6.5 or even just upgrade the shaft because my ball flight was ballooning way up in the air with Golfsmiths launch monitor but I was still averaging 276 yards off the tee with little roll out were as my usual 15° 3 wood averages 250-260 and Driver averages from 280-290. I was hitting indoors so it is a little difficult to comment on the sound but you could definitely hear the difference of a well struck shot from a poor shot and the well struck shot just sounds like you are crushing it. So right off the bat before a shaft change/upgrade I’m already picking up the yardage I was hoping for plus if I get my ball flight down and lower the spin some I could imagine getting some really big numbers out of this. I hope to hit it soon outdoors with a few different options but I don’t see how I could not buy one. I hope everyone else gets to try it soon some good results too!

Reply Report comment
Mike T

Mar 28, 2013 at 11:12 am

This reminds me of the GBB2 3 wood.. I used to have one of those and it was a bomber off the tee, it shape was like a mini-driver almost.

Reply Report comment
Joe W

Mar 27, 2013 at 5:55 pm

Will have to take a look at this. If I can hit it within 5-10 yards of my driver but keep the control I have with my 15* off the tee then I would be happy to give up the driver.

Reply Report comment
Rufiolegacy

Mar 26, 2013 at 9:17 pm

dang it! Just ordered the X Hot Pro last week, I will have to talk to my rep.

Reply Report comment
stu

Mar 26, 2013 at 8:02 pm

Close to a 2 wood. Could see this becoming my predominant club for the tee, relegating driver to a backup for special situations

Reply Report comment
t

Mar 26, 2013 at 3:19 pm

I have been waiting for a product like this for a long time!

Reply Report comment
Jim

Mar 26, 2013 at 12:52 pm

It’s perfect. Can’t wait to get it in my bag!

Jim

Reply Report comment

Cancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Equipment

Tour Edge unveils all-new Exotics mini driver

Published

1 day ago

May 12, 2026

Gianni Magliocco

Tour Edge Golf has today introduced the all-new Exotics mini driver, engineered to deliver a powerful combination of speed, control, and versatility in the long game.

The Exotics Mini combines a titanium face with a stainless-steel body in design to balance ball speed with stability and control, creating a versatile option at the top end of the bag.

At the core of the design is Tour Edge’s proprietary Combo Brazing technology, a high-precision thermal bonding process that seamlessly fuses a titanium cup face to a stainless-steel body into a single, continuous structure. By eliminating energy loss found in traditional multi-piece constructions, Combo Brazing is designed to deliver faster face response, more efficient energy transfer, and a uniquely powerful yet controlled feel.

The multi-material construction also allows mass to be positioned lower and deeper in the head in a bid to increase stability, while the thin titanium face is engineered to maintain ball speed across a wider impact area.

“While the initial goal was to enhance control and versatility in the long game, Combo Brazing ultimately drove measurable gains in ball speed and distance within the mini driver category. In robot testing, we’ve documented higher ball speeds, higher launch, reduced spin, and increased carry and total distance compared to leading models.” – Vice President of R&D Matt Neeley

In addition to distance performance, the Exotics mini emphasizes forgiveness through a heavier stainless-steel body that shifts mass toward the perimeter. This configuration increases MOI relative to traditional all-titanium mini drivers, helping preserve ball speed and directional stability on off-center strikes. Paired with Pyramid Face Technology from the Exotics metalwood line, the design is intended to support consistent speed across the face.

To further enhance MOI, a lightweight carbon fiber crown frees additional mass that is strategically repositioned low and deep in the head in design to improve stability and promote optimal launch with controlled spin.

“We designed the Mini to be about five millimeters shallower than other mini drivers on the market. That change improves playability off the deck. From a clean fairway lie, it can function as a strong 3-wood alternative while still providing control off the tee.” – Tour Edge CEO David Glod

An adjustable hosel system allows for loft and lie tuning to dial in trajectory and shot shape, while a fixed 13-gram rear weight helps stabilize the head through impact to improve dispersion consistency. The Exotics Mini Driver is available in 11.5 and 13.5-degree lofts in right-handed models.

Pricing & Availability

The Exotics Mini Driver is available for pre-order beginning today for $399.99 USD at touredge.com, and will be available for purchase at retail outlets worldwide on May 22, 2026.

Equipment

Srixon ZXi combo or TaylorMade P7CB/770 combo? – GolfWRXers discuss

Published

1 day ago

May 12, 2026

Gianni Magliocco

In our forums, our members have been pitting a Srixon ZXi combo against a TaylorMade P7CB/770 combo. WRXer ‘edutch22’ is on the hunt for a new set of irons and kicks off the thread saying:

“Looking at picking up a new set of irons and think I’ve narrowed it down to Srixon ZXi combo or Taylormade P7CB/770 combo. I am currently a 5 cap and allbeit I feel irons are my weakness. My miss is a little to the toe side. I am decently steep at 4-5 down. Always thought I am high spin but recently on trackman my 7 was spinning at 5800 roughly.

My question or looking for thoughts on which one would benefit me more from a forgiveness standpoint? Or is there another iron is should be looking at entirely? I only get to play about once or twice a week, if I am not playing a 2-3 day event. Thanks in advance.”

And our members have been sharing their thoughts and suggestions in response.

Here are a few posts from the thread, but make sure to check out the entire discussion and have your say at the link below.

manima1: “You just can’t go wrong with Srixon ZXi7.”
MattM97: “You have to hit them to know, the V-Sole on the Srixon can be make or break for many.”
dmeeksDC: “P7CB is more forgiving for me than ZXi7 because my main miss is low middle and the P7CB still flies and spins great on that miss. These are both really nice irons but I like the P7CB more than the Zxi7 and the P770 (or P790) more than the Zxi5. The Srixons are larger so if that gives you confidence that is the way to go. I don’t feel like I get any benefit from the V-sole and the P7CBs live up to their high Maltby forgiveness rating so the TaylorMades have been great for me.”

Entire Thread: “Srixon ZXi combo or TaylorMade P7CB/770 combo? – GolfWRXers discuss”

Equipment

From the GolfWRX Classifieds: 2024 Wilson Staff CB/Blade combo

Published

1 day ago

May 12, 2026

Gianni Magliocco

At GolfWRX, we are a community of like-minded individuals who all experience and express our enjoyment of the game in many ways.

It’s that sense of community that drives day-to-day interactions in the forums on topics that range from best driver to what marker you use to mark your ball. It even allows us to share another thing we all love – buying and selling equipment.

Currently, in our GolfWRX buy/sell/trade (BST) forum, @pianoman0123 has a 2024 Wilson Staff CB/Blade combo up for grabs.

From the listing: “2024 Wilson Staff CB/Blade Combo. 4-8 irons are CB’s and the 9,PW are Blades. 5-PW have Project X 6.0 Shafts and the 4 Iron has a Steelfiber CW110 Stiff Shaft. Standard Length, Lie and Lofts. These are in very good condition the shafts just don’t work for me. Like new Lamkin Grips on the 5-PW and a stock Golf Pride on the 4 Iron. $525 OBO.”

To check out the full listing in our BST forum, head through the link. If you are curious about the rules to participate in the BST Forum, you can learn more here: GolfWRX BST Rules