Opinion & Analysis
Wishon: 7 club fitting keys to improve shot consistency
One of the simplest ways golfers can improve their games is through proper club fitting, which is often overlooked because of the emphasis golf equipment companies place on trying to help golfers hit the ball farther. Adding distance is great, but it doesn’t always come with an improvement in shot consistency. Sometimes, it actually has the opposite effect, whereas a proper fitting almost always improves shot consistency and often leads to more distance as well.
When I speak about shot consistency, exactly what am I talking about? A higher percentage of on-center hits? Sure, that’s an improvement in shot consistency. But so too, and perhaps even more important, are elements of consistency such as a reduction in how far a slice or hook curves off line, or a reduction in the number of poor shots.
Perhaps the best way to express what an improvement in shot consistency means is to help the golfer “miss the ball” better. If you’ve played the game a while, you are well aware of the type of shots that are classified as a “good misses.” No one hits all the shots well. In fact, the best golfers can be said to be those who “miss their shots the best.”
Therefore, the purpose of this article is to offer some of the best fitting tips for “better missed shots” and from it, better shot consistency.
1. A shorter driver, but also shorter fairway woods
At the risk of sounding like a broken record, the percentage of golfers who have improved their tee shot consistency by going much shorter with the length of their driver is nothing short of spectacular. The only male golfers who have a real chance to play well with a 45-inch driver are those with a smooth tempo, great swing rhythm/timing, inside-out to square swing path, later release and good golf athletic ability on top of those things.
For golfers who fall short in one or more of those elements, don’t even think about a driver longer than 44 inches. If the golfer falls short in three or more of those factors, don’t go longer than 43 to 43.5 inches. Longer length only means higher club head speed for golfers with a later-to-very-late release. And even for those with a later release, for 98 percent of them longer length means more off-center hits.
But don’t just think shorter drivers for better shot consistency. Think shorter fairway woods, too. The old fairway wood length standards were 43 inches for a 3 wood, 42.5 inches for a 4 wood, 42 inches for a 5 wood and 41 inches for a 7 wood. Golfers should consider using fairway woods that are a half inch to a full inch shorter than that if they do not possess most of the above ideal swing tempo/release characteristics. You’d be amazed at the improvement in shot consistency from shorter fairway woods.
2. Proper face angle fitting to address misdirection tendencies
Preaching to the choir, element No. 2 for shot consistency is to fit the face angle of the driver, fairway woods and even the hybrids to offset the golfer’s slice or hook tendency with those clubs.
Always keep these two key points in mind when viewing a face angle change for improving shot consistency through better accuracy:
- At a carry distance of 200 yards, a 1-degree change in the face angle from what it was before represents a slice or hook reduction of 4 to 5 yards.
- For a face angle change to work best, you have to know the face angle of your present clubs so you know how much of a change to make to bring about a visible reduction in the slice or hook.
For a face angle change to do its job, you have to address the ball with the face angle sitting as it is designed. All too often, golfers not used to an open or closed face will rotate the head to assume a more square position at address. If you hook or slice and want that to be immediately reduced, you’ll need to just get used to the fact that if you slice or hook the ball, your new face angle is going to sit with the face pointing in the opposite direction of your misdirection tendency.
One last point for golfers with one of the adjustable hosel drivers: The only way these drivers can change the loft is if the golfer always holds the face square in the address position. If you are a relatively straight hitter, fine, you won’t need any face angle help. But if you are a chronic fader/slicer/drawer/hooker, a change in the face angle from what you currently use can be a huge help.
As such, trying to get that from one of the adjustable hosel drivers is difficult and confusing. For that reason, it is best to work with a club fitter who knows his stuff and can source the right driver head that has both the loft AND face angle you need.
3. Matching total weight and swing weight to the golfer’s transition, tempo and strength
If the total weight and/or the swing weight are too heavy for the golfer, more off-center hits, pushed shots and thin shots can result. If the total weight and/or the swing weight are too light for the golfer, a more outside-in path, slice and off-center hits can result.
While we talk a lot in fitting about the total weight (shaft weight) and the swing weight as separately fit elements, from a shot consistency standpoint you have to think of the two working together. For many golfers, the swing weight (meaning the head weight FEEL) is more important for shot consistency improvement than the total weight.
Typically, the more forceful the transition, the faster the tempo and the stronger the golfer, the heavier the total weight (shaft weight) and swing weight would be to best match the golfer’s timing and rhythm. And vice versa, usually the more smooth the transition and tempo and the weaker the golfer, the lighter the total weight (shaft weight) and swing weight would be. It’s not always this way, however, because golfers develop differences in what they think feels best when they swing the club.
It’s also totally possible for golfers with a stronger transition and tempo to end up being well fit into a lighter weight shaft (lighter total weight), but much less likely that a weaker/smoother-swinging golfer would be well fit into a heavy shaft for a heavy total weight.
If a stronger golfer with a little more aggressive transition move were to use a 55-to-65-gram shaft, the light total weight of such a light shaft weight can be offset by using a little to a lot higher swing weight. But on the other hand, it is rarely if ever a good thing to fit a golfer with a smooth transition/tempo and below average strength with a shaft that weighs more than 75 grams, but then try to mute that heavier shaft effect with a low swing weight.
But do remember, weight fitting also has to take the golfer’s personal, acquired preference for the weight feel of the clubs into account. There can be infrequent times when the weaker/smoother-swinging player prefers a heavy feel while a strong/aggressive player could possibly like a lighter feel.
In the end, there is no such thing as a total weight/swing weight detector in fitting. You start with the tendencies of swing force versus club weighting listed here, then experiment to find the combination that works best. In the end, the right total weight and swing weight is found when the golfer never has to make any type of conscious move or effort to control his swing tempo and timing.
4. MOI match the woods and the irons instead of swingweight matching
Ask any mechanical engineer. If the goal is to build all the clubs in a set so they swing with exactly the same effort and feel, the best way to do that is to build the clubs to have the same MOI rather than the same swing weight. MOI matching has been around now for 10 years so the statistics are starting to show tendencies.
When the MOI is chosen properly for the golfer, again based on his transition, tempo, strength and personal FEEL preference, the subtle improvements show up as more on-center hits more often, fewer pulled and pushed shots and a few more greens hit in regulation. But what MOI is right for each golfer is still a guess-and-check process.
The way the best club fitters do it is to build a test club of at least the 5 or 6 iron that possesses everything BUT the weighting the golfer needs in his fitting. The club has the right length, loft, lie, shaft and grip, but the head weight is left light. Then the golfer goes through a process of hit three shots, after which weight is added to the head. This process is repeated until the point is found when the golfer definitely perceives the head weight to be too heavy and too laboring to swing consistently on tempo. A fitter then backs off some of the weight and that becomes the benchmark club from which the MOI is measured and then duplicated on the other clubs in the set.
Final point: For the vast majority of golfers, the best MOI for the driver and woods will be +60-to-70 g/cm2 (the MOI measurement increment) higher than what was found to be the golfer’s best MOI in the irons.
5. Set makeup changes: so underappreciated, but so important
One of the most overlooked fitting factors that will assuredly improve overall shot consistency and deliver better misses for golfers is the set makeup. The whole concept of proper set makeup fitting is to get rid of hard-to-hit clubs and replace them with clubs that hit the ball the same distance and are easier to hit more consistently.
I am talking about the following elements:
- Having an alternative “control driver” of shorter length and higher loft. It can be used in lieu of the normal driver for courses with a greater number of tight tee shot holes, or for days when the swing is not as much “in sync” as other days.
- No three wood for the majority of golfers. Many should start with a 4 or 5 wood, unless the golfer definitely has the skill to consistently hit a fairway wood with 14-to-15 degrees of loft off the ground well up in the air.
- Having more woods, and definitely a 7 wood for most average players. Even a 9 wood for many golfers will work well, especially if the golfer tends to sweep the ball and/or has an early to midway release. And make it a little shorter as well.
- More hybrids instead of more fairway woods? As the golfer’s release gets from midway to slightly later than midway, and as the golfer can consistently hit down and through the shot, the option leans for more hybrids instead of more fairway woods to avoid the hard to hit low-lofted irons.
- Use one more hybrid than the golfer thinks he/she should use. Get the golfer to be totally honest in answering this question, “What is the lowest number iron I can hit consistently well 4 out of 5 times from normal lies?” If he is an 8-handicap golfer or lower, make that iron the break between the last hybrid and first iron in the set. If he is above an 8 handicap, add on one more hybrid and start the irons one number higher than what the golfer thinks he should use. Today’s much lower-lofted irons are fine as long as the golfer is honest in admitting what iron number sees the first big increase in inconsistency and starting the hybrids there. Don’t let ego get in the way of a smart set makeup that allows you to hit more greens and score better.
- Additional wedges. Or rather, tailor the wedge set makeup to the grass, sand and green design of the golf course(s) the golfer plays the most. It is very smart for a golfer to have different wedges of different lofts and sole designs so he can pick the wedge set makeup for the course he happens to be playing that day (this is a big topic to know what wedges to play for what differences in turf, sand and green design, and one I promise to write a detailed story about it in the future).
6. Grip size and feel for comfort
Forget the hand size/finger size charts that golfers use as a deciding factor for grip size. Fit for grip size ONLY on the basis of golfer comfort. Regardless of hand/finger size, the best grip size for every golfer is the size that he feels is most comfortable and allows him to maintain a secure hold on the grip with the least amount of grip pressure with the hands and forearms.
One more thing about grips versus shot consistency: Scrub/wash your rubber grips every other round, and lightly sand the rubber grips every 1 to 2 months as needed with 220- to 240-grit sandpaper. Keeping grips feeling more new can most definitely can help the golfer maintain a higher level of swing and shot consistency.
7. The correct lie angle for ALL the clubs
You’ve all seen the diagram that shows the ball going left when the toe end of the club head is up at impact and the ball going right when the heel side of the head is up at impact.
It goes without saying that dynamic lie fitting eliminates all possibility of an ill-fit lie from ever causing an offline shot. As such, why NOT do it? And think about getting your woods and hybrids fit dynamically for lie. Can’t find anyone with fairway woods and hybrids that can be bent to accommodate a wide range of lie fitting needs? If you look hard enough, you will. They do exist.
I can’t tell you enough in strong terms how valuable all of these fitting keys can be for your score and your enjoyment of this great game. Don’t pooh-pooh these fitting elements as either being less important or something only for mid-handicap players and above. They work to deliver better misses, which in turn means lower scores. Have fun, and as always the very best to everyone in this great game.
Opinion & Analysis
Brandel Chamblee PGA Championship Q&A: Rose’s huge McLaren risk, distracted LIV pros and why Aronimink suits the bombers
PGA Championship week is here, and Brandel Chamblee did not hold back in our latest discussion ahead of the season’s second major.
In our 2026 PGA Championship Q&A, golf’s leading analyst made the case that PIF pulling LIV’s funding has left its players competing in a state of confusion, called Justin Rose’s mid-season equipment switch a huge risk at 45, and explained why Aronimink will be a bombers’ delight this week.
Check out the full Q&A below.
Gianni: With the PIF confirming that they’re pulling funding from LIV at the end of the season, what impact do you expect that to have on the LIV players competing at the PGA Championship?
Brandel: I would imagine that they have all been thrown into a state of confusion, and will be distracted, not knowing where they are going to play next year and not knowing exactly their road back to either the DP World Tour or the PGA Tour. Or in Rahm’s case, being tied to a sinking ship for the next few years, likely playing for pennies on the dollar in events that no one cares about or watches.
I doubt this would put him in the best frame of mind to compete at his highest level. Keeping in mind, however, that majors are the only time that LIV disciples get to play in events that matter, so never disregard the motivation they have to prove to the world they are still relevant.
Gianni: Justin Rose switched to McLaren Golf equipment mid-season while playing some of the best golf of his career. What do you make of the change?
Brandel: I don’t really know what to make of Rose switching equipment. It seems a huge risk on his part, even though it is likely, in my opinion, that the clubs he’s playing are similar, if not the exact grinds, to what he was playing previously, with a McLaren stamp on them.
Having said that, at best, it is a distraction when he seemed to be as dialed in with his game as any 45-year-old could be and trending in the majors to perhaps do something that would definitely put him in the Hall of Fame. At worst, given the possibility that these clubs aren’t just duplicates of his old set stamped with McLaren on them, he’s made an equipment change that would take time, and 45-year-old athletes don’t have the time to do such things.
Gianni: Aronimink has only hosted a handful of professional events since it hosted the 1962 PGA Championship. What kind of test does it present, and does a course with less recent major championship history tend to level the playing field?
Brandel: Even though Aronimink has only hosted a handful of meaningful professional events, it has been fairly discerning in who can win there. When Keegan Bradley won the BMW Championship on the Donald Ross masterpiece in 2018, he was the 2nd best iron player on tour coming into that week. When Nick Watney won the AT&T at Aronimink in 2011, he was 2nd in strokes gained total coming into the week.
In 2020, Aronimink hosted the KPMG Championship, and Sei Young Kim won. On the LPGA that year, she was first in greens in regulation, putts per green in regulation, and scoring average on the way to being the LPGA player of the year. And then there is the 1962 PGA Championship won by Gary Player, who eventually became just one of a few players to win the career grand slam on the way to winning 9 majors. It is a formidable test, and if it’s not softened by rain, it will bring out the best in the upper echelons of the game.
Gianni: Is there a specific hole at Aronimink that you think will do the most to decide the winner?
Brandel: The hardest hole at Aronimink in each of the three tour events that have been played there since 2010 has been the long par-3 8th hole, with the par-4 10th being the second hardest, so most of the carnage will happen around the turn, but with the par-5 16th offering opportunities for bold plays and the tough closing holes at 17 and 18, the finish is likely to be frenetic.
Gianni: The PGA Championship has always sat in the shadow of the other majors. What does the ideal PGA Championship look like in your eyes, and what would it take for it to carve out its own identity?
Brandel: The PGA Championship, to whatever degree it suffers from the comparison to the other three majors, is still counted just as much when adding them up at the end of one’s career. Almost 1/3 of Nicklaus’ major wins were the five PGA Championships he won. Walter Hagen won 11 majors, five of which were PGA Championships.
Tiger Woods twice in his career won back-to-back PGA Championships, and those four majors count just as much as the other 11 he won. The PGA may not have the prestige of the other three, but it carries the same weight. Having said that, I preferred the identity that it had as the last major of the year.
Gianni: You nailed your Masters picks. Rory won, Scottie finished solo second, and Morikawa surged to a tie for seventh. Who are your top 3 picks for the PGA Championship and why?
Brandel: I am not a huge fan of majors played on golf courses that have been shorn of most of the trees, although I understand some of the agronomic reasons for doing so and of course the ease with which it allows members to play after errant drives. However, at the highest level, it all but eliminates any strategy off the tee and turns professional golf into an even bigger slugfest. That means that it will likely be a bomber’s delight this week, but fortunately, Scottie Scheffler is long enough to play that game and straight enough to play it better than anyone else.
The major championships give us very few surprises anymore, going back to the beginning of 2012, so the last 57 majors played, the average world rank of the winners has been better than 15th in the world. So look at the highest ranked and longest drivers who are on form coming into the PGA Championship who also have great short games as the surrounds at Aronimink are very challenging. That’s Scottie Scheffler by a mile and then McIlroy and Cameron Young with a far bigger nod towards DeChambeau than I gave him at the Masters.
In this episode of the Club Junkie Podcast, we dive into one of the most interesting flatstick releases of the year with a full review of the new TaylorMade SYSTM 2 putters. After spending time on the greens, I break down what makes this design stand out, where it performs, and why it has me completely torn between loving it and fighting it. If you are into feel, alignment, and consistency, this is one you will want to hear about.
We also take a look at some of the putters in play on the PGA Tour last week. From familiar favorites to a few surprising setups, there is always something to learn from what the best players in the world are rolling with under pressure.
To wrap things up, I walk through the process of building a set of JP Golf Prime irons paired with Baddazz Gold Series shafts. From component selection to performance goals, this is a deep dive into what goes into creating a unique custom set and why this combo has been so intriguing.
This year my 50th birthday. Gosh, where has the time gone?
As a teenager in rural Missouri, some of my junior high and high school years felt interminable. Graduation seemed light years away. But the older I get, the faster life seems to fly by.
I’m also increasingly aware of my mortality. My dad died recently. Earlier this year, a friend and fellow PGA of America professional and I were texting about our next catch-up. The next message I received was news of his unexpected passing at 48. Shortly after, a woman I dated in college succumbed to cancer at 51.
Certainly, one can share perspective at any age. Seniors help freshmen, veterans guide rookies. But reaching this milestone feels like as good a time as any to do one of those “what would I tell my younger self?” articles.
I’ve had a uniquely varied career in golf. I started as a 27-year-old, average-length-hitting, 14-handicap computer engineer and somehow managed to turn pro before running out of money, constantly bootstrapping my way forward. I’ve won qualifiers and set venue records in the World Long Drive Championships, finished fifth at the Speedgolf World Championships, coached all skill levels as a PGA of America professional, built industry-leading swing speed training programs for Swing Man Golf, helped advance the single-length iron market with Sterling Irons®, caddied on the PGA TOUR and PGA TOUR Champions, and played about 300 courses across 32 countries.
It’s been a ride, and I’ve gone both deep and wide.
So while I can consult and advise from a lot of angles, let me keep it to a few things I’d tell the average golfer who wants to improve.
1. Think About What You Want
Everyone has their own reason for picking up a golf club.
Oddly, as a professional athlete, I’m not internally driven by competition. That can be challenging, as the industry currently prioritizes and incentivizes competition over the love of the game.
For me, I love walking and being outdoors. Nature helps balance my energy. I prefer courses that are integrated into the natural beauty of their surroundings. I’m comfortable practicing alone. I’m a deep thinker, and I genuinely enjoy investigating the game, using data and intuition to unearth unique, often innovative insights. I’m fortunate to be strong and athletic, so I appreciate the chance to engage with my abilities. Traveling feels adventurous. I could go on.
You don’t have to overthink it like I do. For you, it might be as simple as hitting balls to escape work, hanging out with friends, and playing loosely with the rules and the score.
The point is to give yourself permission to play for your own reasons, and let that be enough.
But if improvement is your goal, thinking about your destination—and when you want to get there—is important, because it dictates the steps you need to take. When I set out to go from a 14-handicap to the PGA TOUR as quickly as possible, the steps I needed were very different from those of a working golfer trying to break 90 in six months. That’s also different from someone who just wants a few peaceful hours outside each week, away from work or family.
None of these goals are better than the others, but each requires a different plan that you can work backward from.
2. There Are Lots of Things That Can Work
One of the challenges of golf is that, although there are rules for playing, there aren’t clear, industry-wide standards for how to best play the game. There’s a lot of gray area.
You might hear a top coach or trainer insist that a certain move is the best way to swing or train. Then you dig a bit deeper and, much to your confusion and frustration, another respected coach or trainer says something completely different. I don’t think anyone is trying to confuse you—at least I hope not. It’s just where the industry is right now.
You have to be careful with advice from tournament pros, too. They might be great at scoring, but they’re also human and sometimes just as susceptible as amateurs to believing things that don’t really move the needle. Tour players might describe what they feel, but that’s not always what they’re actually doing when assessed with technology.
I recently ran a test on my YouTube channel (which connects to my GolfWRX article “How to use your hands in the golf swing for power and accuracy”), and, interestingly, two of the most commonly taught hand actions produced the worst results in the test.
Coaches can certainly help. If you find someone you connect with to help navigate, that’s great. But there are many ways to get the ball in the hole. In the current landscape, you may need to seek multiple opinions, think critically, and use your own intuition to discern what seems true and whose advice resonates with you.
I’d recommend seeking someone who is open-minded and always learning, because things constantly change. Absolutes like “correct” or “proper” should raise a red flag. AI can be useful, but it tends to confidently repeat popular advice, so proceed with caution.
3. Get Custom Fit
If you’re serious about becoming a better player, getting custom fit is hugely important. There’s no sense fighting your equipment if you don’t have to. Most better players get fit these days and, if they don’t, they’re usually skilled enough to work around clubs that aren’t ideal.
If you plan to play for a long time, it’s worth spending a little more upfront to get something that truly fits you and your game, rather than continually buying and discarding equipment.
Equipment rules haven’t really changed significantly since the early 2000s. To stay in business, manufacturers keep pushing those limits. If you pull a bunch of clubs and balls off the rack and test them, you’ll find differences. I’ve tested two new drivers and seen a 30-yard total distance gap. Usually, the issue isn’t bad equipment; it’s that the combination of components simply isn’t the best fit.
It’s like wearing a new pair of floppy clown shoes. Sure, they’re shoes—but you won’t sprint your best in them compared to track shoes that fit perfectly.
Be wary of what’s called custom fitting, too. Sometimes the term is used as a marketing strategy rather than an actual fitting. In some retail settings, fitters may be incentivized to steer you toward higher-priced components. That doesn’t automatically mean it’s not the best fit, but you should be aware of potential biases.
I learned a version of this lesson outside of golf. Years ago, I bought a tennis racquet at a big box store from a seemingly knowledgeable employee who thought it would suit me best. The racquet gave me tennis elbow, and I spent months recovering with rest and acupuncture. The next season, I invested more time and money to find what actually fit me, and I walked away with something amazing that I still play with years later.
So if you’re going to get fit, be smart about it.
Find someone you believe has deep knowledge—possibly with certifications, but not necessarily. Make sure there’s a wide inventory across many brands. Check recent reviews for the individual fitter if possible. Make sure you trust that the fitter has your best interests at heart. If they’re wearing a hat or shirt with a specific brand’s logo, proceed with caution. Unless you specifically want a certain brand or look, be wary of upsells, especially if two options perform nearly the same.
Also, while golf is called a sport of integrity, there’s a thread of manipulation in the industry. I once drafted an equipment article for an industry magazine, structured just like one of their previous popular stories, with matching word count and great photos. The assistant editor loved it; it was useful to readers and required little work on his part. But the editor-in-chief nixed the story. When I asked why, I was told it was because I wasn’t an advertiser. It turned out the article I’d modeled mine after was a paid ad cleverly disguised as editorial content.
I really dislike games, clickbait, and fear-based manipulation. I hope this changes, but golfers deserve to know it exists.
4. Distance and Strategy Matter
There’s a real relationship between how far you hit the ball and your scoring average, even at the PGA TOUR level.
I experienced this early in my pro career. I started as a power hitter, swinging in the high 120s and breaking 200 mph ball speed with a stock driver.
Back then, some instructors advised swinging at 80%, so I tried slowing down for more accuracy. That worked fine on shorter, tighter courses. But on longer setups, I was coming into greens with too much club, and par 5s stopped being
RBC Heritage Tour Report: More minis, course-specific setups, Spider & GTS launches
Justin Rose WITB 2026 (April): Full WITB breakdown with new McLaren irons
Best fairway woods of 2026: The most versatile fairway woods + the most forgiving fairway woods
What’s the story behind Webb Simpson’s custom-stamped irons?
Cadillac Championship Tour Report: Spieth’s sizable changes, McLaren Golf launches, and more
The 24 players who can win the Masters
Rory McIlroy’s winning WITB: 2026 Masters
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
J.J. Spaun’s winning WITB: 2026 Valero Texas Open
Cameron Young’s winning WITB: 2026 Cadillac Championship
Alex Fitzpatrick WITB 2026 (May)
Driver: Ping G440 LST (9 degrees) Shaft: Fujikura Ventus Black 6 X 3-wood: TaylorMade Qi4D (15 degrees) Shaft: Fujikura Ventus...
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
Driver: Ping G440 Max (9 degrees) Shaft: Mitsubishi Tensei 1K White 60 TX 3-wood: Ping G440 Max (15 degrees) Shaft:...
WITB Time Machine: Rory McIlroy’s winning WITB, 2021 Truist Championship
Rory McIlroy’s victory at the 2021 Wells Fargo Championship 2021 (now the Truist Championship) marked a significant return to form,...
Collin Morikawa WITB 2026 (May)
Driver: TaylorMade Qi4D LS (8 degrees) Shaft: Mitsubishi Diamana D+ Limited 60 TX 3-wood: TaylorMade SIM Tour (14 degrees) Shaft:...
-
Equipment2 weeks agoJustin Rose WITB 2026 (April): Full WITB breakdown with new McLaren irons
-
Equipment1 week agoWhat’s the story behind Webb Simpson’s custom-stamped irons?
-
Equipment2 weeks agoCadillac Championship Tour Report: Spieth’s sizable changes, McLaren Golf launches, and more
-
Whats in the Bag3 days ago
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
-
Whats in the Bag1 week agoCameron Young’s winning WITB: 2026 Cadillac Championship
-
Whats in the Bag3 weeks agoNelly Korda WITB 2026 (April)
-
Equipment2 weeks agoJustin Rose on the switch to McLaren Golf, learnings from previous equipment moves
-
Tour Photo Galleries2 weeks agoPhotos from the 2026 Cadillac Championship
Don Koes
Jan 7, 2021 at 4:42 am
Hi Tom,
In regards to MOI matching, is there any general rules of MOI increment between iron set vs hybrid vs woods vs driver?
Thanks a lot.
rob huget
Nov 7, 2016 at 10:10 am
Tom I have ordered your 575 mb 5 to the gap also your driver. When I ordered my previous set of mizuno mp 32 they were 2 degree’s flat, when Ross Beebe in Chilliwack measured the shafts they were an inch longer than standard. Is this normal if you are going to flatten the degree’s to have the shaft longer. Also I would assume lie fitting for the driver would be the same as the irons, if impact is more to the heel the lie should be flatter. Thanks Rob Huget
Pingback: Improving Slim Shots For Sale | petsloseweight.com
Jim
Jan 20, 2015 at 10:53 am
Tom, I would like to learn how to be a club maker and fitter, I have
read your materials and have some fairway woods from you and
very happy with clubs and your knowledge. So what I am asking is
your advise on how to go about this venture. Thanks Jim
PS I live Massachusetts
zzkevinw
Feb 20, 2014 at 4:03 pm
Thanks Tom,
I’m 60 years old, fit and athletic, a 21 handicap, and have played for 4 years now. I’m ready to buy my first set of new clubs, and put the yard sale clubs in the basement. Whenever I’m listening in on a fitting session at a golf store, the whole experience seems daunting and a bit dodgy, as if it’s only about how much money they can talk you into spending. I’m very green when it comes to the golf-club lingo and such. Can you steer me toward a competent, trustworthy fitter somewhere near either York, ME or Worcester, MA? Cheers.
Starving Golfer
Feb 11, 2014 at 12:04 pm
Tom,
Any recommendations for club fitter/maker in Nashville, TN?
Regards,
Scall1968
Feb 6, 2014 at 2:13 pm
Tom,
How long until the wedge article?
Tom Wishon
Feb 7, 2014 at 5:37 pm
Well the WRX editors were talking to me today about what’s next. Are you asking about how to choose the right wedge for you and your game?
Iain Clarke
May 24, 2014 at 10:57 am
Hi Tom ,
I am also very interested in you forthcoming wedge article as I am currently producing a my own line of wedges via a manufacturer in Fujian , I read part of an article where you were promoting the virtues of a company called Vtech in Tiawan . would it be possible for you to recommend at contact at the company please.
Iain
Zdenek
Feb 6, 2014 at 10:44 am
Hi Tom! I would like to buy first driver for my girlfriend. Like Mizuno EZ driver – 44″ ladies spec…What is you recommendation – something like 42-43? Thanks Zdenek
Tom Wishon
Feb 7, 2014 at 5:36 pm
Need some more information about her.
1. What is the measurement of the distance from her wrist to the floor while standing comfortably erect, shoulders level, arms relaxed at her sides, standing on a hard surface floor in flat sole shoes.
2. What is her avg score or handicap
3. Is her swing path outside in, square or inside out
4. Is her swing tempo, smooth/easy, forceful and aggressive or somewhere in between these
5. Would you say that she is above average in her athletic ability, about average or below avg
Get that info to me and I will be happy to offer the best recommendation for her so the length does not get in the way of her being as good as she can be, yet it can be comfortable for her too.
TOM
Zdenek
Feb 8, 2014 at 10:24 am
Hi Tom many thanks!
1. 82cm (32inch)
2.112, but know in winter we trained a lot with PRO
3.inside out
4.slow backswing, fast change to agressive downswing
5.above average athletic ability
Mike
Feb 6, 2014 at 10:18 am
Great insight Tom. Always learn something from your articles and posts on the site. Just made the switch to heavier shafts in my driver and fairway wood and definitely see a big difference and less Slices. Not to mention cutting the driver down to 44″ and 3 wood to 42″ for better consistency. Looking forward to reading more of your articles.
Bo svensson
Feb 2, 2014 at 9:32 am
Thanks tom for an excellent article. I am really keen after reading this to make a proper set for myself. Do you have any experience of teeview, a club fitter in stockholm, sweden? Or recommend someone else in the area?
Thanks in advance!
Tom Wishon
Feb 7, 2014 at 5:39 pm
Tee View is OUTSTANDING in clubfitting. Seriously, Conny and Leif are really good, very experienced and without question you WILL walk away with the very best fit you can possibly get. (and I bet you did not know that Leif is a former Olympic athlete for Sweden) Don’t hesitate to call them – your golf game will love them when you are finished!
Jack cheney
Jan 30, 2014 at 1:42 pm
Tom, great article, and I told Glenn Malmquist you said hello. He is 88 years young and still active. He says hello to you and keep up the good work! Thanks, jack
Tom Wishon
Feb 7, 2014 at 5:41 pm
I bet he is still active. Shoot, from what I remember about his energy level when I used to talk to him regularly in clubmaking back in the 80s and 90s, he is going to outlive every one of us here! And you tell him that too!
Christian
Jan 24, 2014 at 3:13 pm
Hi Tom, thanks for the article. I have a question specifically about Hybrid fitting. I have been trying very hard to find a 2H with mixed results. I’m a 1 hdcp and play a straight or small draw, can’t hit a fade to save my life. I’ve owned three 2hybrids in my search and am finding a pattern. The 2h’s I’ve tried from a tee produce an unexpected big fade and often start right of target. I’m not sure why it is the only club in my bag producing these results. All shafts have been stiff at 75-80 grams.
So the question is, what are the most important spec’s to consider when getting fit for a 2hybrid? Thanks Tom.
Christian
Tom Wishon
Jan 29, 2014 at 1:08 pm
It is difficult to know for sure what could be causing you to fade the ball this much with this hybrid when you do not do that at all with any other club. Typically for that to happen, the face angle of the hybrid would have to be much more open than any of your other clubs. But as a 1, I would think that you would see this when you put the club down in the address position. Really from all my experience for a really good player to fade/slice one club only would point to this having a much more open face. Only other thing would be if the headweight feel was much too light for your swing tempo, but here again as a 1, you would have noticed that right away.
I tend to see hybrids as irons, meaning to be the same length as an iron of that same loft. Most all OEM hybrids are made to lengths that are longer by 1″ to 2″ than what an iron of the same loft would be. Now for you as a 1, that length should not be an issue. Only other thing I can add is to experiment with your ball position with this hybrid. Some hybrids by virtue of their length play more consistently when a little more forward ala a fwy wood, while others require from their length to be played a little back, like halfway between left heel and center.
Christian
Mar 12, 2014 at 1:05 pm
Thanks for the reply Tom. I have since tried another 2 different 2h which produced big hooks. I’m starting to think I just don’t know how to hit a 41″ 2h 17* club specifically.I don’t know enough about shafts to compare and all 5-6 2h’s I’ve tried have all had different stiff shafts. At this point I think I’ll go find a fitter just to find a 2h I can become “friends” with. I have 13 clubs that are my close “friends”, can’t wait to figure out what my issue is with 2h’s and find one to fit into my set. *still searchin*
Don Porter
Jan 23, 2014 at 6:52 pm
I have been more accurate with my driver since I started choking up. Does shortening the club help more than just choking up?
Tom Wishon
Feb 7, 2014 at 5:43 pm
As Mr Penick taught me years ago, he preferred the term “gripping down” on the club as there is just this “other” connotation with the term “choke”. . . . cough cough. ((!!))
Gripping down is fine as an alternative to physically cutting the club shorter as long as the smaller grip diameter that brings about is not uncomfortable to you. That’s really the only downside to gripping down because grips are all tapered in their diameter.
Brian
Jan 20, 2014 at 1:47 pm
Hey Tom, I am a 4 handicap living in Minot, North Dakota. I have been looking into a new set of irons as well as a new 3 wood. I am 6’4″ and have used standard length, lie clubs my entire life. My problem with my irons is that my misses with my short irons tend to be a blade, and my problem with my 3 wood is that it feels way too light for my swing/swing speed. Any suggestions on an experienced club fitter in my area? I would really like to know what it feels like to swing properly fitted clubs.
Thanks,
Brian
Tom Wishon
Jan 20, 2014 at 5:16 pm
Brian
Ouch, sorry about the fact that custom clubmakers are scarce up in your neck of the woods. In such cases when there is not a decent clubmaker in someone’s area, we have a program where we can help you. If you would please send us an email at contact@wishongolf.com we will be glad to explain how we can help you.
Thanks
TOM
Chris
Jan 28, 2014 at 2:26 pm
Brian,
If you ever get the chance to stop in at an Austad’s Golf in Fargo, they have a store there. Talk to Nick, he is the manager at the store and would probably be of great help to you. I work at one of the other stores and Nick is a very nice guy. It would definitely be something I would consider if you wanted to get fit off a launch monitor.
James brown
Jan 17, 2014 at 8:31 pm
Just had elbow surgery on left elbow. I’m looking to do a whole new club set. Dr. Says to go with graphite shafts. I had the UST recoil prototype put in my mp-69 and have just hit today the wedge and 9 iron. How good they feel and different also. Can you tell me of a very good Wishon clubfitter in North Carolina? I am in High Point-Greensboro area. That’s in central part of state.
I have spent my last 2-3 months on the shelf reading your material. Thanks, james
Tom Wishon
Jan 19, 2014 at 12:57 pm
I can offer two recommendations not too far from High POint. Steve Thornton in the Winston Salem area at 336-817-6907 or StevesRxGolf@aol.com – or in the Thomasville area, Special Tee Custom Golf at 336-887-3333.
Thanks very much for using my reading material to help you get through the re hab period! Best to you!
AJ Jensen
Jan 16, 2014 at 12:57 pm
Funny you mention this about the 7-wood. A friend of mine has an old seven and he uses it for so many different shots, and with such good results, I’ve had my own eye out for a seven just like it.
With the recent trend toward higher lofted drivers, do you see fairway woods making a similar loft increase? I ask because I’m in the market for a new fairway wood, after hitting a Stage 2 HL model with 16.5 loft, and in the simulator it seemed to outperform my current Burner 1.0 13-degree spoon.
Tom Wishon
Jan 19, 2014 at 11:28 am
No, actually fairway woods have undergone a very slight loft decrease over the past 30 yrs – like irons but not even close to as much of a loft decrease as with the irons. Up to the 80s, 3 woods were all 16*, 4 wood was 19*, 5 wood 22*, 7 wood 25*. These days the avg 3 wood is 14-15, 4 wood 16-17, 5 wood 18, 7 wood 21 and 9 wood around 24.
The reason higher loft drivers hit the ball farther as swing speed is slower while with fwy woods and irons that isn’t the case has to do with the relationship of swing speed to how much the ball can keep flying up and up in the air on a lower launch angle. For most golfers, that “point of reverse return” when less loft means more distance comes at around 16, 17, 18 degrees – also depending on swing speed for sure. But once you get to 20*+ almost all golfers will hit a lower loft longer in distance because the height of the shot at higher lofts keeps the ball up in the air with enough spin to allow the ball to fly as far as the ball speed allows. With slower speeds and lower lofts, you just do not have the ball speed or spin to keep the ball up in the air longer enough to really fly to the maximum distance the ball speed would allow. So more loft on the driver means more distance for slower speeds because the loft launches the ball higher and with more spin to keep the ball up in the air longer.
Where the slower swingers have to be careful with woods is to generally not try to use a 3 wood unless you have a 90mph speed and have good swing fundamentals. Today’s 14-15 3wood lofts are just too low for slower swing speeds and especially for slower speeds + less that great swing characteristics to hit well up to fly.
JRUt
Jan 16, 2014 at 11:23 am
Tom,
Great article. It really applies to those of us whom are “vertically challenged.
What are your opinions regarding club fit and the growing junior golfer? Should they be fit twice a year, or more?
It’s been an interesting 18 months with multiple growth spurts.
Tom Wishon
Jan 19, 2014 at 12:51 pm
Having remembered when the growth spurt hit with my son, I certainly understand what you are going through. Usually though the faster it happens, the sooner it will calm down so changes in the length of the clubs can be limited. In general, with more athletic kids, if their initial jr clubs were fit properly for length, you can figure that for each 4″ they grow in height, the clubs would need to get another 1 inch longer. This is a basic average and for sure can be different due to kids’ differences in height vs arm length. But for economics sake, it would be best if you could extend the length of the clubs for the first length increase you need up to an increase of +2″. Then when you need to go longer than that, you would need to re shaft or get new sticks.
Steelydan
Jan 16, 2014 at 4:53 am
Tom,
Thanks for the great article. For a tall guy like me with relatively short arms (wrist to floor is 39″), would you rather start an iron fitting with upright lie or with longer shafts? I hear so many different opinions about this. Most recommend to limit shaft length and increase lie angle, but I understand length is not so much of a problem in irons? Would +2″ still acceptable?
Thanks
SD
Ken Christopherson
Jan 15, 2014 at 10:40 am
Tom, as usual, you make sense. Thank you. I think any one of your books is a great place for someone to start to get an idea of how they are handicapped by not having equipment that fits them and their game. It is interesting that Titleist used to write on their website that less than 5% of customers can use off the shelf clubs effectively, and that most golfers would benefit from being custom fit. Each of us needs: different swing weights, different club lengths, different lie and face angles, different grip sizes, matching clubs to MOI, the correct choice of shaft weight & flex, all to fit our specific athletic and physical characteristics. You are a voice of reason and effective common sense in a market filled with marketing hype.
dman
Jan 14, 2014 at 12:15 pm
Tom, I find it hard get a hold of good clubMAKERS. Can you recommend someone in the LA area? East side if possible? There are so many guys out there at these big box stores that really don’t know what they are doing or are just careless. Thanks.
Tom Wishon
Jan 14, 2014 at 4:04 pm
Based on my limited knowledge of LA geography, a really good clubmaker in what I perceive to be “sort of east” LA would be Ron Burleson of Corona Custom Golf in Corona – 951-279-9663 or ron@coronacustomgolf.com (www.coronacustomgolf.com). And then further east would be Philip Moore of Exact Golf in Cathedral City – 760-904-5198 or 951-377-6268 / underpar45@aol.com. I’ve known both of these men for some time, have had them at clubfitting seminars over the years, and can testify they both know what they are doing for sure in serious clubfitting.
dman
Jan 14, 2014 at 6:21 pm
thank you very much!
Stan Szczsponik
Jan 11, 2014 at 7:22 pm
Tom,
Wondering if you can recommend someone in Rhode Island, Massachusetts or Connecticut to perform the fitting. If not, are you available and where are you located?
Thank you.
Stan Szczsponik
Coventry, Rhode Island
Chad
Jan 12, 2014 at 3:48 pm
Stan,
Tom Spargo – Spargo Golf in Cranston, RI
spargogolf.com
You won’t be disappointed!!
Tom Wishon
Jan 13, 2014 at 7:18 pm
Real quick Stan to echo what Chad told you about Tom Spargo. I know him personally from him being at a number of the clubfitting seminars I have done over the years and he is VERY good.
Tanner
Jan 10, 2014 at 7:43 pm
Good info Tom. As a life long 25-30 handicapper, should I forget the
the proper core turn and swing from the ground up and just get the face
fixed? I will say, I don’t have an issue of a slice. The problem is usually a lack of distance or a proper strike where my ball falls short of the target. Will these changes help there or is it more to fix
a slice?
Cheers
Tanner
dman
Jan 14, 2014 at 12:12 pm
this is a very specific question for a high handicapper. go see a pro who is also a clubfitter!
Phil Marshall
Jan 10, 2014 at 7:46 am
Superb article, I have followed conventional wisdom and industy maketing down some blind allies eg lighter shaft, total club weight, that were inappropriate for me. Amazing results from trial and error outcomes that so closely match Tom’s real wisdom. This shaft weight and head weight matching to a golfer is just so impotant to performance.
Tom, I think another book is warranted.
Thanks so much
Dennis
Jan 10, 2014 at 12:37 am
Hi Tom,
Great article, has got me thinking and reading more shafts. I play Mizuno MP 58 with DG S300 shafts that play well. Woods and hybrid not so much. These are also Mizuno. Driver MP 630 10.5 deg, 4 wood mp 16.5 deg, 20 deg hybrid mp clk. What shaft would be best to get the same feel in these as the irons?
Thanks
Tom Wishon
Jan 13, 2014 at 7:21 pm
Most players who like the feel of the Dynamic Gold do need to get themselves into a tip firm shaft as well for the woods. Problem is there are MANY tip firm shafts in woods in MANY varying levels of tip stiffness. So the bottom line is really to see if there is a really experienced clubfitter in your area with whom you can work so he can better evaluate the shafts you have used in the woods that are not quite right, then from that he can get a better idea of where you need to go next with the wood shaft. What town/city do you live in/near? Let me know that and I can look to see if there is such a good clubfitter in reasonable proximity to where you live.
Chuck
Jan 9, 2014 at 10:09 pm
This is just a stunningly intelligent article. I’ve been playing with a 42.5″ steel (DGLite X100) 3-wood for 12 years. TM 200 Tour “smoothie”. I would not take $400 if someone wanted to buy it from me.
And I plan to build myself a 43.5″ steel (DGSL) driver this year; probably a SLDR 430.
Experimenting is fun, easy and enjoyable when the shafts cost $14.95.
Thank you for all of your wonderful writing, Tom.
Shallowface
Jan 9, 2014 at 6:03 pm
The tricky part about grip size is the different amounts of taper from one shaft to another. Some shafts taper very little, and some taper a great deal. When you’ve got a driver with one shaft, fairways with another, hybrids with another still and then the set of irons, getting that grip size consistent, especially under the trail hand, can be a chore. But it’s necessary if you’re going to have a consistent grip with every club.
Loop
Jan 9, 2014 at 5:39 pm
Tom fantastic info on the budget MOI fit for irons. Thanks. With the 3/8 length changes, do the lie angles have to also be adjusted accordingly?
Tom Wishon
Jan 9, 2014 at 6:51 pm
Lie angle always should be rechecked dynamically whenever a golfer changes lengths on his clubs (or if you’re dead serious when you change shafts, change swingweight/headweight too).
LY
Jan 9, 2014 at 2:45 pm
Tom:
I saw a big improvement in my consistency when two years ago I changed my set make-up so that the 7 iron was the first iron in my bag. I volunteer at an LPGA event every year and I get a chance to look in a lot of the players bags. I noticed a very high percentage carried more than one hybrid. So I’m thinking to myself on the drive home, if the best women players are using more than one hybrid then how come I’m not.
James
Jan 9, 2014 at 2:22 pm
Mr. Wishon, what is the best way to ensure my current driver, if cut down to 44 inches from current 45.5, is weighted properly? Unfortunately in my area, clubmakers are rare and most things I have to do myself.
Tom Wishon
Jan 9, 2014 at 7:01 pm
Get yourself some lead tape and head to the driving range. After warming up through the bag, hit 2-3 shots, add 2 strips of lead tape, each 4″ in length (anywhere you want on the head – though flat across the sole is a real easy place to put it) hit 2-3 shots, add tape and so on.
What you want to do is note the feeling of the head’s weight during the whole swing, backswing, transition and then downswing while hitting shots and progressively adding a little weight. Do this until you start to feel that the head’s weight is feeling a little on the heavy side to you. Then back off 1-2 strips of the lead tape and hit 3-5 shots with that, and see if you feel that you need to drop any more headweight from a FEEL standpoint of it still being a little heavy.
Then several days later come back to the range, warm up, then hit 3-4 drivers with the club as you finished weighting it the last range session and reflect on that headweight feel one more time to see if you sense whether the weight feel of the head on the end of the shaft still feels pretty good, not too heavy and not too light.
It really is best to do it this way so you do not get trapped into a specific set swingweight measurement. Some guys will add weight back to the head after shortening the club to make the shorter club’s swingweight the same as what it was at the longer length. Lots of times if you do cut 1″ or more from the length, that becomes too much headweight when you add weight to get the swingweight back to the same as it was at the longer length. Swingweight is not an actual weight – it is simply an expression of the relationship of weight on one end of the club vs the other. When you change length dramatically, the swingweight that represents the best headweight FEEL for your swing timing and tempo won’t likely be the same at the shorter length as it was at the longer length.
Hence the reason to have to go through a hit a few, add weight, hit a few, add weight – and reflect on the headweight FEEL as you keep doing this a little at a time. You’ll find that point where the weight feel of the head during the swing is not too heavy and not too light. And that’s where you stop and forget it from then on as you head out to play.
TOM
Ron
Jan 18, 2014 at 1:58 pm
Tom, love your posts. I’ve got a Nike Covert that I have to choke up about an inch or so to hit consistently, but I was hesitant to cut it down. It’s the stock length which is 45.75 which is way too long for me, even as a 3 handicap. I’ve got a very aggressive swing with fast tempo so I’m right in the category you say will benefit from shorter driver length. If I lop off 1.75 inches, I’m afraid that’s going to take an awful lot of lead tape. Any ballpark of how many strips I’ll need? If it helps, my favorite driver of the past few years was a Callaway Razr Fit with a whiteboard x73 that measured D6. I went away from it last year when I gained about 20 pounds, lost flexibility from less play, and lost about 8 MPH swing speed. I haven’t been fully properly fit since my fitness declined but I just tweaked based on feel. Any advice for a fitter in central NJ?
J.A.
Jan 9, 2014 at 1:51 pm
Tom, what about proper iron length? If you recommend shortening woods by a half to a full inch, would that also be suggested for irons?
Tom Wishon
Jan 10, 2014 at 11:29 am
No, irons over the years have not increased inordinately in length as have drivers and fwy woods. If you go back to the 80s before this length increase began, drivers were 43″, 3 woods were 42″, and the 5 iron std length was 37 1/2″ Today we see the avg driver at 45.5″ with some at 46″, the avg 3w is 43 to 43.5, but the avg 5 iron length is 38″, representing only a half inch increase.
So irons have not “gotten out of line” nor have they increased in length to the point that the modern length could be a performance problem for golfers.
Duncan Castles
Jan 9, 2014 at 1:24 pm
As always, fascinating and informative. And it all works.
Tom is too modest to mention it, but his excellent hybrids, fairways and drivers can be easily adjusted to the correct lie angle without the use of any weight-adding, deceptive hosel device.
Ralph Patterson
Jan 9, 2014 at 12:39 pm
Tom,
Someone asked if you should shorten the driver, 3-wood etc. by cutting the butt or the tip of the shaft but I never saw your answer. What’s the best way to shorten them?
Thanks,
Ralph
Oldplayer
Jan 9, 2014 at 3:39 pm
Always the butt. Cutting the tip can change the flex characteristics dramatically.
Conrad
Jan 9, 2014 at 12:23 pm
I’ve always played 46 in my driver, tried shorter shafts but gained little to no accuracy from it. Drivers always been solid as its the best club in my bag
Tom Wishon
Jan 9, 2014 at 4:40 pm
If you have the time, find my article on How To arrive upon your best lengths which is floating around the tech forum and has been getting some more commentary so it is not too many pages deep in that forum.
You’ll find the exact description of how to know what golfer swing characteristics indicate that longer is better or shorter is better. In general, the smoother/more rhythmic the transition and tempo, the later the release, the more square to slightly in/out the path, the flatter the plane and the better the golfer’s sense of feel and timing, the more they could play well with longer lengths.
The opposite of these swing characteristics all add up to say shorter is a must. I’m betting if you do well with 46″, you possess many to most of the above swing characteristics.
Jeff Burns
Jan 9, 2014 at 12:14 pm
Which one of these tips will give me 17 extra yards? Ha.. I joke, I kid!
Great article Tom and I’ve very happy to see vindication for my 7 wood in here. I’ve even carried a 9 wood in the past and it’s been a huge help. I’ve taken my driver down to 44.5 but I might go shorter and bring the 3 wood down with it.
Thanks for the excellent information.
J
DB
Jan 9, 2014 at 8:46 am
Shorter driver and fairway wood really is the #1 tip. I can’t understand why more amateurs don’t do it. I see all these guys, even shorter guys, with 45.5-46″ drivers.
I’m 6’1″, and went to 44.75″ driver and 42.5″ 4-wood. Both D3. I love it, will never go back to anything longer. In the fairway more often, and I don’t even think I lost any distance. Still have the same clubhead speed.
Bryce
Jan 9, 2014 at 9:56 am
Hi
Shorter with tip cut to make stiffer or butt end cut?
Thanks 🙂
Tom Wishon
Jan 10, 2014 at 11:30 am
When shortening an existing club, cut from the butt end. And then go to work with lead tape to see what headweight increase is necessary to get the headweight FEEL comfortable during the swing.
Mats "PUMP 2" Bergsten
Jan 9, 2014 at 7:52 am
Tom,
Great article, as always when you decide to share your thoughts and knowledge!
Living in Sweden I use David Leet, PGA Pro at Falsterbo GK, to fit my clubs. He uses all the equipment to get my clubs MOI matched and all other variables as well. Very much into details, as well as I am. Reading your articles and visiting you website, givs me a better understanding, when collaborating with him, in a strive to get the best fitted equipment for myself and my game.
Keep up the good work!
Tom Wishon
Jan 9, 2014 at 12:00 pm
Matz:
Thanks much and just wanted to echo that you couldn’t be in a better place for your golf! Not only is Falsterbo such a great links, but David Leet is truly a “pro’s pro” in every facet from teaching to training to fitting to being one of the nicest people on the planet. And it is great that your club is continuing to work on improving the links with the course revisions you are making. I’ve been very fortunate to have been to your club several times. I wish I could own a house in the neighborhood and be a member and hang out there a lot.
Rich
Jan 9, 2014 at 7:39 am
I have been in the golf retail industry and buying gold equipment on a regular basis in the Australia (Sydney) for the best part of 20 years now. There is no one (green grass or off course retail) that would know how to do this kind of detailed fitting here. It just does not exist. I know more than any (maybe all put together) of the people (including club pro’s) working in golf retail in my area, about golf equipment, shafts, tech data and performance, full stop. I was even fit for a set of Titleist irons in the last 12 months or so and the fitter had to refer to a book (fitting manual of some kind) because he didn’t know how to fit me properly. Needless to say I didn’t buy the irons. Fitting here in Sydney Australia is a buzz word, not something that people know how to do. I’m not sure there is anyone that knows how to do it properly in my experience. The only people I have left to try are the Ping guys here in Sydney. When I’ve spoken to them on the phone, they sound like they actually know what they are doing but I haven’t tried their fitting process out yet so I may have to give them ago the next time I’m in the marker for something.
Tom Wishon
Jan 9, 2014 at 12:18 pm
Do you know Gary Tozer at Aussie Custom Golf up in Gateshead? http://www.aussiecustomgolf.com – 417 297 266 . Maybe about 60 miles from Sydney.
Oldplayer
Jan 9, 2014 at 3:44 pm
What about Melbourne Australia Tom? I have experienced the same as Rich and find it hard to get fitted properly. Sydney is 800 Kilometers away.
Tom Wishon
Jan 9, 2014 at 4:35 pm
Ahhh, Melbourne you are in LUCK!!!! Call Geoff Waldon on 39 439 8151 or email him at geoffwaldon@intermode.on.net and book a fitting appt as fast as you can. Geoff is REALLY GOOD, very experienced and has been doing this on a low key basis for quite a number of years now.
TOM
Rich
Jan 9, 2014 at 4:30 pm
Thanks Tom. Gateshead is about a 90-120 mins drive from Sydney but’I might have to get in touch with him. Cheers.
Brandon
Jan 9, 2014 at 12:58 pm
Pure Performance Golf Labs Sydney location opens at the end of January. Over 30,000 combinations and every brand that is not only fit but then hand built to those exact specs.
Pureperformancegolflabs.com.au is the website
Rich
Jan 9, 2014 at 4:59 pm
Thanks Brandon, I will check them out too. Cheers.
JohSte
Feb 26, 2014 at 8:57 pm
Hi Rich
see Dave Reckless at Dural Golf Driving Range.
In the best 100 fitters in the world.
sam Brooks
Jan 9, 2014 at 4:46 am
Yip I’ve just gone back to 45.5″ driver.. That’s all I need to hear. I’m cutting it down an inch first thing in the morning… Tom says I do!!!
Patrick
Jan 9, 2014 at 3:36 am
Tom, fixing slices a
Robert
Jan 9, 2014 at 3:29 am
Nice article, a lot of good information in there. However, I am sceptical towards changing the face angle. I mean, shouldn’t we as practitioners of the sport strive towards perfecting our technique instead of compensating with equipment in a way that almost encourages swing faults?
Tom Wishon
Jan 9, 2014 at 12:07 pm
Without question golfers should work on their swings and do their best to keep improving their swing characteristics. But the hard cold fact is that not that many golfers have the time, money or commitment to take the lessons and work as hard as is required to make permanent swing changes. Not only that but the swing moves required to hit the ball straight are most definitely body movements that not that many people have the athletic ability to do – to master a square to slightly inside out swing path with a later to very late release are two very challenging movements for less athletically inclined people to master.
To natural athletes, these things are not that difficult to do so they can’t imagine why all golfers can’t do it. but it is a fact that with MANY golfers who swing over the top, outside in and slice the ball, no matter what they will never master a swing path and release change to be able to turn that slice into a straight ball.
It is for those golfers that face angle fitting stands as one of THE most important game improvement elements that can be used to enjoy the game more. And according to Golf Digest, over 70% of all golfers do slice the ball to some degree – so that’s a whole lot of golfers who could enjoy the game more if they did draw upon face angle fitting as part of their fitting improvement work.
paul
Jan 8, 2014 at 11:51 pm
He writes, I read.
P
Jan 8, 2014 at 9:58 pm
Problem is, hardly any fitter has MOI machines. And it takes FOR EVER to do MOI fit.
Ian
Jan 8, 2014 at 9:47 pm
Tom, after getting the weight in the six iron correct how do you determine the proper weight for the rest of the irons. I know there are MOI measuring machines but if you don’t have one what would you suggest the swing weight progression should be?
Tom Wishon
Jan 9, 2014 at 12:11 pm
One can come VERY close to an MOI match by making the irons to be in 3/8″ increments for length AND then making the swingweights to progress upward in 0.5 swingweight point increments down through the set. So let’s say the ideal 6 iron you find is 37 1/2″ and D1. Starting with the #7, the lengths get shorter in 3/8″ increments per iron and the swingweights go D1.5 for the #7, D2 for the #8, D2.5 for the #9, D3 for the PW. And on the other side of the #6, the #5 becomes 37 7/8″” longer and D0.5, the #4 becomes 38 1/4″ and D0. WE joke around and call this the “poor man’s MOI match” but it is a VERY close approximation of using the $500 MOI machine to do the match for the clubs in the set.
P
Jan 10, 2014 at 3:26 am
If that is true, then why do we even need the machine?
Tom Wishon
Jan 13, 2014 at 7:23 pm
Only if you get concerned about the clubs being perfectly matched for MOI within 1 to 2 g-cm2 or if you are ok with being close within say 10-15 g-cm2. for most golfers, the progressive swingweight approach will be close enough.
John Muir
Jan 8, 2014 at 8:38 pm
Great article. I like the driver/control driver/5 wood set makeup idea.
John
Deck
Jan 8, 2014 at 6:33 pm
I recognize that photo!
As usual another Fantastic article Tom.
Tom Wishon
Jan 9, 2014 at 12:20 pm
Hey Deck!! Thanks! Staying warm up there? And like us, counting the minutes until spring?!! HA!
Merty Huckle
Jan 8, 2014 at 6:12 pm
good stuff.
tom stickney
Jan 8, 2014 at 6:08 pm
Fantastic article….big fan of your work, sir!
melrosegod
Jan 8, 2014 at 6:01 pm
It’s refreshing to read intellegent thoughts based on precision experience rather than “smash-boom” hype. Thanks Tom!
Jeffrey Trigger
Jan 8, 2014 at 5:48 pm
I play an R1 Black with a Kiyoshi white shaft, I had it cut down. I actually hit it further than my longer shafted driver. I play an RBZ Stage 2 Tour HL 3 wood that is a quarter inch shorter than standard. I will never again play a 15 degree 3 wood. Absolute monster. I have a 4 hybrid and 4 through PW. All of those are two degrees upright. I like slim wedge grips on all my clubs. Although finding 580 core grips can sometimes be very hard.
Andrew
Jan 8, 2014 at 5:43 pm
Very insightful as ever Tom. Gone to a 44″ driver earlier this year after reading some of your other articles and the consistency difference is massive…still thinking of going shorter as well along with shortening the 3 wood/3 hybrid to more ‘old school’ lengths.
Was fitted and Went to four wedges last year and have never looked back. Got 46/06, 50/08, 54/11, 58/6 to make sure distance gaps are covered. Santa brought me some higher bounce options to help with the softer winter conditions in the UK and they’re working well also and should give me options through the summer I guess
People really need to look at this especially given some of ‘std’ (very strong) lofts manufacturers are using.
tiger168
Jan 8, 2014 at 5:42 pm
Back to the basics, awesome article, this will be an instant classic.
Pingback: Tom Wishon: 7 club fitting keys to improve shot consistency | Min kärlek till golfen...
Dwaine Ingarfield
Jan 8, 2014 at 5:37 pm
Great article. I am a big believer in using a shorter than new standard driver.
Tom Wishon
Jan 9, 2014 at 6:50 pm
From 1905 to 1985, “standard” length for a men’s driver was 43″. And believe me EVERY company followed that as their standard driver length. having worked in the golf equipment industry since 1980 and doing head design work since 1986 it has always been interesting to be to wonder just why did that “standard” grow some 3″ in the years from 1985 to present day. Golfers didn’t get taller or grow shorter arms over the past 28 yrs. I’ve always wanted to ask the golf companies for an answer to that question.