Equipment
Titleist Vokey SM5 Wedges
Titleist’s new Vokey SM5 wedges offer golfers more tour-preferred grind and bounce options, as well as more spin from their larger third-generation Spin Milled grooves.
The new “TX3” grooves have a 7-percent larger groove volume in two different configurations. The grooves are deeper and narrower on the 46-to-54 degree wedges than the previous generation to deliver better distance and trajectory control, reducing the chance of flyers from the rough.
“On tour these guys have to aim to a lot of small targets,” said Aaron Dill, who builds and grinds Vokey wedges for PGA Tour players. “They need to trust that their golf ball will travel the exact distance they need it to, even from a tough lie in the rough. The deep and narrow TX3 groove helps push the grass down better, which gives you that increased edge radius contact for more spin and consistent distance.”
Above: A Vokey SM5 56-degree wedge with 10 degrees of bounce, an “M Grind” and a “Raw Black” finish.
On the 56-to-62 degree SM5 wedges, the grooves are the same width as the previous generation, but they have a greater depth that adds roughly 400 rpm more spin on full shots from the rough, according to company testing.
“The groove configuration changes with the [56-degree] model because this is where testing showed that the player makes a more oblique impact versus a more direct impact in the lower lofts,” said Master Craftsman Bob Vokey. “The wider TX3 groove on the higher lofts will sheer away the grass, rather than pushing it into the groove, and perform better on partial shots.”
The SM5 wedges are cast from 8620 carbon steel, and are available in lofts from 46 degrees to 62 degrees in two-degree increments. They come in six tour-inspired sole grinds (L, T, S, M, F and K), with each model sorted into low-, mid- and high-bounce categories. That creates a selection of 21 different loft, bounce and grind combinations.
The wedges will be available in stores March 14 in three different finishes — Tour Chrome, Gold Nickel and Raw Black — and will sell for $129. The Tour Chrome and Gold Nickel are plated finishes, while the Raw Black finish will rust over time.
SM5 Sole Grind Descriptions
- L Grind: Narrow crescent sole with small forward bounce surface and minimal camber. Swing type: Slider. Condition type: Firm.
- T Grind: Dual bounce sole with wide trailing bounce surface. Swing type: Slider/Neutral. Condition type: Firm/Medium.
- S Grind: Full sole with straight trailing edge ribbon and moderate heel relief. Swing type: Slider/Neutral. Condition type: Firm/Medium/Soft.
- M Grind: Crescent sole with narrow forward bounce surface and moderate camber. Swing type: Slider/Neutral. Condition type: Firm/Medium.
- F Grind: Full sole with moderate camber and small trailing edge ribbon. Swing type: Slider/Neutral/Digger. Condition type: Firm/Medium/Soft.
- K Grind: Wide sole with increased bounce and enhanced camber. Swing type: Neutral/Digger. Condition type: Medium/Soft.
Equipment
Putters that never made it: Check out some of the best tour builds that didn’t make the cut
Arguably, the best perk of being a professional golfer on the PGA Tour is the ability to request or even just be handed pretty much any club you could think of. It happens more often than you think, usually with putters around the practice green from one event to the next. Come Wednesday, the Tour bags lining the edge of the putting surface become resting places for fallen flatsticks that never made the cut.
So let’s take a look at some of the best we’ve seen out on Tour this year that never made it to the competition. (You may notice none of Hideki Matsuyama’s custom Scotty Cameron putters made this list. There are too many.)
Let’s start with this custom Damascus Milled Odyssey Rossie made for Ryo Hisatsune. Featuring a single line and the short-slant hossel, we’ve seen plenty of Number 7 and jailbird heads featuring the Damascus Milled insert, but this is the first and only one we’ve spotted in a Rossie. Hisatsune primarily putts with an Odyssey Black Series iX #9, but we have seen him recently with a TaylorMade TP Collection SOTO, so there could be potential that the Damascus Milled Rossie could end up in the bag.
Everyone wants to be Cameron Young right now. We’ve had Justin Thomas and Tom Hoge both game the Scotty Cameron 9.5R prototype. Well, for the PGA Championship, Brooks Koepka nearly joined that list after requesting the same style of putter, with the full-length alignment line. But the Scotty Cameron reps took the request a step further and made one specially for Koepka with a Teryllium insert, similar to one in his previous Newport 2 gamers. The reason why this one didn’t go into play, though? Because it was too heavy.
Harry Hall was the third-best putter on Tour last year, so when Bettinardi made him a custom proto, you know it was going to be good. The custom BB28 blade features VDF face milling, a custom-welded single-bend shaft, and the owner’s initials – HH – on the sole of the putter. Hall, who usually games an Odyssey O-Works #7 W, has dabbled with a TaylorMade Spider Tour X already this year. Maybe there’s a chance this Bettinardi might make his bag.
Honestly, this one doesn’t need a description. It’s Kieth Mitchell’s custom Scotty Cameron Napa. One Scotty Cameron face stamp, two Scotty Dogs, two Scotty Cameron 7-Point Crowns and one Circle T. That is all. Oh, except for the Cashmere Cameron headcover.
Finally, and just for fun, how about we pour one out for this TaylorMade Spider Tour X made for Scottie Scheffler in its new torched finish. It’s unlikely we’ll see a putter change anytime soon from the best golfer in the world. In fact, he hit just two putts with it on the Harbour Town practice before going back to his trusty gamer.
Driver: Titleist GT3 (9 degrees) Buy here.
Shaft: Aldila Rogue Silver 130 M.S.I. 70 TX
3-wood: TaylorMade Qi35 (15 degrees)
Shaft: Fujikura Ventus Blue 7 X
7-wood: TaylorMade Qi35 (21 degrees)
Shaft: Fujikura Ventus Blue 8 X
Irons: Grindworks PR-202 (4), Grindworks PR-101A (5-PW)
Shafts: True Temper Dynamic Gold Tour Issue X100
Wedges: Cleveland RTX6 Tour Rack (52-10 Mid), Titleist Vokey Design SM10 (56-08M), SM11 (60-04T)
Shafts: True Temper Dynamic Gold Tour Issue S400
Putter: Scotty Cameron Tour Rat 1.5 Tour Prototype
Ball: Titleist Pro V1x
Grips: Golf Pride MCC
In our forums, our members have been discussing their favorite major winning irons used by Tiger Woods. WRXer ‘golferdude54’ kicks off the thread saying:
“Mizuno MP 14/29. Titleist 681T. Nike Forged Blades. TaylorMade P7TW.
Among these irons that helped Tiger win 15 majors, which is your favorite in terms of looks?”
And our members have been naming their favorites and why in response.
Here are a couple of posts from the thread, but make sure to check out the entire discussion and have your say at the link below.
- SwingBlade: “I prefer the early blades he played and the more recent TM TW’s especially because after Tiger had his major behavioral setbacks, part of Nikes support payback was making Tiger play a Nike putter and cease using his beloved uniquely customized Scotty putter.”
- ProjectX: “This (Nike Forged Blades) and there’s not even a close second.”
Entire Thread: “Which of Tiger’s major winning irons are your favorite? – GolfWRXers discuss”
Justin Rose WITB 2026 (April): Full WITB breakdown with new McLaren irons
RBC Heritage Tour Report: More minis, course-specific setups, Spider & GTS launches
What’s the story behind Webb Simpson’s custom-stamped irons?
Cadillac Championship Tour Report: Spieth’s sizable changes, McLaren Golf launches, and more
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
Cameron Young’s winning WITB: 2026 Cadillac Championship
Aaron Rai’s winning WITB: 2026 PGA Championship
Nelly Korda WITB 2026 (April)
Justin Rose on the switch to McLaren Golf, learnings from previous equipment moves
Photos from the 2026 PGA Championship
Patrick Reed WITB 2026 (May)
Driver: Titleist GT3 (9 degrees) Buy here. Shaft: Aldila Rogue Silver 130 M.S.I. 70 TX 3-wood: TaylorMade Qi35 (15 degrees)...
Aaron Rai’s winning WITB: 2026 PGA Championship
Driver: TaylorMade M6 (9 degrees) Shaft: Aldilda Synergy Blue 70 TX 3-wood: TaylorMade Qi10 (15 degrees) Shaft: Fujikura Ventus Blue...
Michael Block WITB 2026 (May)
Driver: TaylorMade Qi4D (9 degrees) Shaft: Fujikura Ventus Black VeloCore+ 5 X 3-wood: TaylorMade Qi4D (15 degrees @14.25) Shaft: Mitsubishi...
Bryson DeChambeau WITB 2026 (May)
Driver: Krank Formula Fire Pro (6 degrees) Shaft: Project X Prototype 3-wood: Krank Formula Fire (10 degrees) Shaft: LA Golf BAD...
-
Whats in the Bag3 weeks agoKristoffer Reitan’s winning WITB: 2026 Truist Championship
-
Whats in the Bag2 weeks ago
Aaron Rai’s winning WITB: 2026 PGA Championship
-
Tour Photo Galleries3 weeks agoPhotos from the 2026 PGA Championship
-
Equipment2 weeks agoGolfWRX Launch Report: 2026 Titleist GTS drivers
-
Equipment2 weeks agoPGA Championship Tour Report: Fitzpatrick, Koepka among big-name putter switches for Aronimink
-
News2 weeks agoWITB Time Machine: Phil Mickelson’s winning WITB, 2021 PGA Championship
-
Equipment2 weeks agoWhich of Tiger’s major winning irons are your favorite? – GolfWRXers discuss
-
Equipment2 weeks agoLead Tape Report: Adjusting the swingweight of the Wanamaker Trophy
Leglikewood
Feb 15, 2016 at 3:16 pm
What would be the standard bounce/grind setup for a 56 and 60?
Curtis
May 1, 2014 at 12:52 pm
Can’t wait for my wedgework sm5’s this weekend!!
Brian
Mar 22, 2014 at 1:33 pm
What’s the difference between tour chrome finish and gold nickel finish? Durability wise? Purely cosmetic?
Gary Lewis
Mar 22, 2014 at 3:04 pm
I think it is pretty much cosmetic. The Gold might not reflect the sunlight as much as the chrome.
Brian
Mar 23, 2014 at 11:29 am
Thanks! I have black nickel irons and was hoping for a return of that in the wedges but I don’t mind the gold nickel.
Gary Lewis
Mar 2, 2014 at 9:57 am
Nice looking wedges and Vokey is continuing to try to improve on a winning formula, and I would bet they will kick ass on the marketplace. Sounds like Vokey has been able to increase the performance with the grooves. Kudos on that. I have just bought a few of the Cally Mack Daddy 2’s, which I like very much, but the SM5 looks like another winner too and it appears he likes Mizunos idea on the grooves. Can’t wait to see these in person.
Jericho
Feb 5, 2014 at 3:13 pm
just had a set of mp-4’s built matched with x100’s played Monterey on my birthday for the first time with these was 4 under through 14 then gave it back away for an even par 71 ..I’ll take it.. with that said..do I get mp t4 wedgeswith s400 to keep the same feel or wait for sm5’s..kinda leaning towards mp t4 ?
Rich
Jan 22, 2014 at 4:14 pm
Never been excited about a Vokey line before but I’m very keen to see these. I’m getting sick of my ’09 X Forged wedges (even though the original MD grooves were cavernous!) and these look nice.
simon
Jan 22, 2014 at 3:01 pm
Very much like my Mizuno’s design only with less feel.
There does seem to be more options with the SM 5 but the lack of forging keeps the Mizzy’s in my bag.
sam Brooks
Jan 22, 2014 at 1:31 pm
Yea sounds like they have use mizunos quad cut idea.. Mizunos have some crazy bite on partials even when chipping you can control the spin really well.. Hmm yea think I’ll stick with mizzys
Chris S
Jan 22, 2014 at 7:35 pm
absofreakinlutely. I bought two Vokey wedges for a total of nearly $400 last year and they won’t be in the bag this year. I would be willing to pay more for forged versions because the grinds are great. Just wish the feel was there.
sam Brooks
Jan 22, 2014 at 1:30 pm
Sweet..
Mark Burke
Jan 22, 2014 at 9:28 am
When I was living in the Tubes in Palm Springs. I never thought I would see a day when vokey would offer so many options on their stock wedges. Now if I can only get my shot on tour, I can maybe use these wedges to get me to the promise land. My caddy New York is coaching me up right now, this year is the year I clear my name.
Harry Dorton
Jan 21, 2014 at 10:25 pm
Look like every other Vokey of past 15 years.
Chris G
Jan 21, 2014 at 9:12 pm
So excited for these. Has noticed a big drop in spin on partial shots with SM4’s. glad to see they fixed that issue. Raw Black in 46,54 and 60 for me please.
Harry Dorton
Jan 21, 2014 at 10:24 pm
I am sure it is the club.
Troll
Feb 24, 2014 at 9:16 pm
Harry’s taking out his 18th hole frustrations on everyone else
Phil
Jan 21, 2014 at 2:44 pm
Sounds like Mizuno design with the different grooves.
Kimmy
Jan 21, 2014 at 1:39 pm
Does Raw Black mean it will rust?
Deaus
Jan 21, 2014 at 2:31 pm
Yes, it will rust. Rust can provide extra spin some say. If you dont like the rust you can use an oil that Vokey has, or stuff I use called SCHUTZ, I have a set of PVD irons that rust really easy but this oil prevents it.
Dave
Jan 21, 2014 at 3:16 pm
Does the oil mess with spin? More of a question of whether oil residue stays on the club, which I would expect to impact spin / crisp contact.
John Aiello
Jan 21, 2014 at 12:30 pm
These look great. My only wish was that they did not add the bounce number in red below the loft number on the toe of the club. I think it looks cheesy.
Jeremy
Jan 21, 2014 at 9:56 am
Will all of the SM5 finishes be offered in Left Hand?
Cole
Feb 5, 2014 at 4:37 pm
The tour chrome and raw black are available in LH but I am not sure about the gold nickel